Hi all,
I'm deploying an nRF9160-based device in India and hitting the familiar "which SIM actually works here" wall. Looking for current (2026) experiences, since older...
Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi,
I am working on nrf52832, s132, SDK17, trying to trigger the saadc with the RTC2
This is my setup :
what I am trying to do is to periodically trigger a series...
I am using a custom board using the nRF52832. I have developed a number of applications using this board sucessfully using nRF5 SDK.,
I am porting a current application...
Project Zip:
Following is my setup:
Board : NRF52832 by Sparkfun( Link ) - Added pull-up resistor for TWI
Sensor: LIS2DH12(Custom breakout)
IDE: Segger Studio...
https://devzone.nordicsemi.com/f/nordic-q-a/79832/need-interface-mcu-initial-boot-firmware
apparently i can't update it anymore. does 'engineer assigned' mean that it can...
Hello,
I was measuring the current of a circuit I made using a PPK II and noticed I am getting two different readings from the two PCs I used (a work and a home PC).
Both...
hi
my first test do not run, bletooth is not enabled and could not get the bluetooth device led on board and signal on my mobile.
i following this link
https://infocenter...
Dear team,
i am working on ble_app_lbs_nus_c project when in this project try to add nrfx_timer.c file
we got an error like this.
and in sdk_config.h file is there ...
Hi,
I am receiving NRF9160 board. Please let me know if we need to change anything to support India Bands. Also it will be great if you can share Indian service provider...
How do I quickly check if the external crystal (32.768 with 15pf load caps.) I soldered is working.
I built a custom board but had to reflow solder in my lab.
Everything...
Dear DevZone community,
I'm developing a Mesh application using nRF52840 Segger Embedded Studio (SES) onLinux. I'm using version 5.0.0 of the Mesh SDK. As desccribed in...
Hi all, I have integrated a slightly customised Ble to Uart example with the buttonless DFU implementation and libraries, and obviously its size inflated. I need to decrease...
Hi. I am trying to generate a shared key via ECDH to encrypt message through UART between nrf52832 and Qualcomm chip. nRF52832 is using uECC and Qualcomm is using openssl...
Hi engineer,
I have developed a dongle that uses 52840 and is used as the master device. Now the data sent by the dongle to the slave device needs to use prepare write request...
Hi,
I have just started playing with nrf connect sdk.
Things I have achieved so far:
1. Build the code.
2. Download the sample codes.
3. Evaluate the performance...
Hey all,
I've run into an interesting situation where writing multiple notifications to successively to a multi-characteristic (custom) service causes data loss. Look like...
