After updating the nRF Kconfig VS Code extension to version 2026.9.356 , the Kconfig GUI can no longer be opened.
When attempting to open the Kconfig GUI, VS Code shows...
Dear Nordic team
we have customer would like to know if nRF93 support voice ， like voLTE or simple using Application-layer voice solution over the LTE data channel?
they...
nrf54l05, SDK NCS3.0.0, using MCUboot, with external PY25Q16HB as new firmware staging area. During upgrade, attempting to observe CLK waveform, a test wire was soldered onto...
Hi
I'm using NRF54L15 DK from Nordic. I have installed VS Code and NRF Connect SDK and toolchain V3.4.1.
I'm following the Fundamentals course, and doing Lesson 1, exercise...
Hello,
We are seeing a west build reproducibility issue on nRF Connect SDK v3.4.0 that we have narrowed down, through extensive elimination, to the compiler's code generation...
Hi,
I'm using the Thingy:91 X PCA20065 rev 2.0.0 as a reference for a new nRF9151-LACAA1A design, and I would like to make sure I understand the recommended correction for...
Hi,
I'm using the Thingy:91 X PCA20065 rev 2.0.0 as a reference for a new nRF9151 design, and I have three related questions about BUCK1 and the 1.8 V rail.
1. nRF5340...
I am working through the nordic sdk 8.1 peripheral heart rate monitor example. I am wondering what RR is? I can't figure out what it stands for or what the purpose of it is...
Hi,
In my current project I have indicating LEDs connected via TWI bus. In this case, I can't use BSP_LED_0/BSP_LED_1 outputs to indicate states as it implemented in nrf_ble_dfu...
Hello, I recently use nrf52832 to make a wireless sensor network of BLE concurrently with NRF_ESB.
During development, I use only 2 sensor. Both sensors are connected to...
ANT S212, nRF52:
I've read all the links in the forum regarding serial port running in debug mode and not in run mode.
In my case, it works in RUN mode until softdevice_setup...
Hi
I have a sensor array which data have to be advanced burst to one or many devices.
The array size is anything from 24 bytes to 24k bytes, depending on the number of...
Hi guys,
I am using nrf51822 and SDK 11. I have some trouble about suddenly reset the nrf51822.
In my application, I used uart_fifo to received some information from other...
Hello beacon fellows,
with regards to maintenance, i am looking into the possibilities to avoid human presence when updating the message to be emitted by Beacon Kit. Any...
Hi,
I'm trying to do (customized / simplified) dual bank DFU on NRF52832 as simple as possible, without any complicated checks.
Assume I succeeded into storing the new...
i want to know about how nrf51822 beacon's states will change once it is turned ON.
with the state diagram i can define how the module is working after turning it ON.
...
Hi,
I am trying to configure the nRF52832 on my custom board to work on the 32.768KHz clock signal from the host controller. I have configured the LFCLKSRC register to use...
Hi
I have a problem with my NRF52 DK and my HEX file ..
With one of my projects, when I generate a HEX file, and I put this one in the NRF52 DK, the program is not working...
I'm fairly new to nRF ecosystem and embedded studio. I'm just trying to read GPIO read of my digital hall sensor. Can anyone find what am I doing wrong with my code? I just...
Hi,
I generated by DFU package following the BLOG post: devzone.nordicsemi.com/.../
However I had to make some changes as it seems to be out of date. I used the following...
