I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hi,
We are currently evaluating the NRF9151 for asset tracking using the AT firmware on the NRF9151 evk and an external MCU for the application firmware, emulating the final...
Hello,
We’re Bachelor’s students developing a project to estimate the angle of arrival (AoA) using a BLE antenna array on the nRF52833. Our implementation builds on Zephyr...
Hi,
i have a strange problem which happens when i use scan mode to get 3 separate channels on saadc.
For example when i use uint32_t ticks = nrf_drv_timer_us_to_ticks...
Hi, I use Keil 5 and SDK 13.0.0 in Windows 7 64bit desktop.
I wished to test the SDK 13's BLE UART example.
However, even though I clicked "Check for Updates"...
basically i tried am trying the easiest ble example
ble_app.becon_pca10040
i tried the following.
use keil to upload into the nrf52 Evalutaion board. the led is...
Hello, i have been looking for a good development environment to use for my nrf52832 on linux. I have only found a few repositories on github pertaining to this. Not very...
Hello,
Does someone know a good J-link segger for programming the nrf51822 smart beacon kit?
And do u need a 6-pin j-link segger for the nrf51822 smart beacon kit?
hello ,
I am interfacing Grideye AMG8832 with Nrf51822. The initialization part is executed without errors but ON trying to recieve or transmit it gives error of TWI as...
Hi Nordic developers.
I am developing a custom board using 2 Rigado BMD-300, but I am unable to run my 100% operative program or examples.
At first time I was able to...
Hello,
I am using SDK 12.2 currently but I would like to follow the BLE Tutorials offered on this site, which I see were written for SDK 11.0. Will I have any issue following...
Trying to program an MDBT42Q nRF52832 based BLE module from an nRF52-DK as external target on connector P20.
I used to do this with nRF51-DK and external nRF51 modules with...
Our product is a peripheral on the nRF51822. We develop on Mac and use gcc, make, etc with Visual Studio Code rather than Eclipse. Recently, we started getting close to production...
Hello,
I would be interested on knowing whether I may have a secondary UART on the nrF52 chip or not. I would like to communicate my nRF52 with a RN2483 and this is done...
Hi
I've just looked into the new released SDK 13.0.0 with support for the new S132 4.0.2 and the new PCA10056. On line in the release notes reads "This release does not...
I'm using the serialization code with pc-ble-driver for S130 (version 0.5.0).
I randomly get a deadlock in the serialisation code.
It can happen after a call to read, write...
Hi,
I want to know that what should be the supply voltage to NRF52 IC. Another thing is that we want to connect our product with NRF52. Our product has TTL wires which...
Hello,
Is there any methods to implement the "long press wake-up"? Pressing the button for 3 seconds to let device enter sleep mode and pressing the same button for 3 seconds...
