Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi all,
I have ublox nina modules including your nrf52833 .
I downaloaded the ublox application here:
Release C209 AoA Tag v2.0.1 · u-blox/c209-aoa-tag
and opened...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi,
I'm using zephyr RTOS.
I'd like to put the cpu System ON Sleep Mode to conserve power.
Then, I'd like to restart the CPU with an interrupt or event from the comparator...
Dear Staff,
we have some Ublox C2909 TAG based on your nRF52833 chip.We need to program them for an RTLS project.
In particular we need to:
customize the FW here ...
Hello,
I managed to run the examples for nrf54l15 channel_sounding_ras_initiator.c and reflector on my custom hardware boards. I changed the overlay files to use my own...
Hello,
I am using a custom board and my setup looks like this:
nrf51 chip
16KB RAM
256KB of Flash
external crystal of 32MHz
SDK12.1
Compiling on Linux...
Hello,
I am trying to read values from MPU9250, I can read them from accelerometer and gyroscope but when I try to read from magnetometer i cant get any values on UART...
I'm working with the SAADC peripheral example and I'm trying to add some code to set the ADC resolution. I've tried doing this several different ways based on what I can find...
I am working with the nRF51 (PCA100028) dev kit and the nRF51822 beacon to monitor the RSSI of the beacon via the nRF51. To do so, I installed nRFconnect and connected the...
Hi,
I would like to have a confirmation of my interpretation of the consumption information that I found in the NRF51822 product spec to estimate the power consumption...
Hello,
reading the revision history in the S130V2 document, it seems only documentation has been changed.
Are there any specific functionality / bugfixes / api changes...
i want to use 2-wire to do the communication of two nrf24le1. one is the master, another is slave.
I don't know how to set up the master and slave.
Is it the code shown...
Hello All!
I am going to use nRF52832 as a network co-processor. I will be using UART as the interface between the main processor and nRF52832.
My question is how to go...
Hi,
i update my characteristic every 1 second with a new value. the notification is set for the characteristic and it will notify my phone about the new value.
at the...
I have a PCA100028 not working anymore. not sure what I have done to the board.
I have a couple of other PCA100028's work well on the same computer.
The program left on...
hi
its first in this event
on_ant_evt_channel_closed
and then
storage_access_complete_handler();
then it try to advertise by this
sd_ble_gap_adv_start...
I use s130 /center ble_hrs example , add 7 peripheral characters and add dfu,but when I want to update codes, I find it start dfu,start bootloader and connecting.... all the...
hi.
in s110 there is no problem but when use example ble_ant_app_hrm in s310 nrf51422 the ble getting error.
its error code is 536881912 :( .
in debug point error ocure...
hi.
i wrote a program in s110 and it work fine . in it i creat my own service .
but when i want use my service in s310 softdevice in this line i get error forbiden or error_code...
