Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
As per the datasheet of nrf52840 any peripheral like SPI/UART/... can be configured to any of the GPIOs so is the QSPI also.
But at Pin details QSPI pins are recommended...
Hello,
We are working on machine health monitoring system. For that we are using nRF52840 SOC as Central and nRF52833 SOC as end node. We had used single Central node and...
Hello.
I'm beginner on Nordic product and checking the examples with nRF5_SDK_17.0.0_9d13099 on nRF52833 DK Board.
I tested ble_app_uart and it works. Now checking ble_app_hrs...
Hello, I am
I'm a Beginner at developing NRF 51822 My Development Environment sdk : 12.3 IDE: KEIL v5 SoftDevices : s130
Recently, I've been experiencing a lot of...
Hi,
I'm trying to find a way to power down and on again a RAM section, but I haven't had any luck finding.
In the SDK examples, there's a RAM retention example only, but...
Hi! I am using nrf52832 with icm20948 (SPI) and I want to put nrf52 in sleep and wake up if there's any motion detected. I am unable to put my device on sleep by the function...
I use nrf_libuarte_async from nRF5 SDK v16.0.0, without softdevice on nrf52840. The idle power consumption of my board is several tens of uA. I call:
and then the idle...
nRF52840, SDK16.0.0, S140v7.0.1
We use SoftDevice (RTC0) and app_timer (RTC1). I'm trying to configure RTC2 and TIMER0 to do PPI-driven crystal timing as described in...
I'm using the empty_app_core project for the APP CPU and my NET CPU binary does not start. I suspect the NETWORK.FORCEOFF is holding the NET CPU in reset upon startup. I tried...
I have encrypted 12 bytes on the nrf51 and sent this + 4 byte MIC across to an Android device.
However, when I try to decrypt on Android using a Cipher with "AES/CCM/NoPadding...
Hello everyone,
I would like to developpe my own custom board, I would like to know if it's simple to replace micro USB by USB C and if someone has already do that to help...
A.
while (true) { while (app_usbd_event_queue_process()) { /* Nothing to do */ } if(m_send_flag) { static int frame_counter; size_t size = sprintf(m_tx_buffer, "Hello USB...
hello I am using nrf52832. I am advertising some data and scanning (on the same microcontroller) for other nrf52 devices(which will have the same firmware). When the other...
Hello,
I'm using SDK v16.0. I'm trying to change the default UART pins from 6,8 to 45,46. In the pca10056.h I have made following changes.
But I still see log on pin...
I am using nRF Connect 2.3.2 on iOS 13.6 on an iPhone 11 Pro Max. I can scan and find my nRF52-DK with the flashed application and the service is correctly advertised (e.g...
