I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hi,
I'm working on a design with nRF52840 on PCIe Mini Size card. Since there is no VBUS rail on PCIe connector and I need a communication via USB, is it possible to bypass...
I see that I can USE BT MESH in an application . Can I encrease the number of advertisingh channel adding some secondary advertising channel?
May I do that in this way ...
Hello,
I come to you because I did not find the information on the web about sending MQTT data. I send a buffer of size 1408 with MQTT but I see in the configuration that...
Here is a screenshot of my current debug session. I cannot figure out why this if statement is failing. I have circled the relevant information. Even the disassembly indicates...
Hello,
I am trying to debug and develop in the net core of the nRF5340 and am having trouble flashing and debugging from SES.
I started by following the guide posted here...
Hello,
My board is connected to Gyro, Magneto sensor.
And board is sleep and wake-up by GPIO.
It usually works well. But time to time after wake-up from sleep mode...
Good Morning!
I try to update the modem firmware of a nRF9160 chip.
When I connect it with the nRF Connect v3.6.1 - Programmer (v1.4.10) and try to update the modem with...
Hi all
For the nRF52832, the total maximum sink and source current is recommended to be 15mA in this devzone entry .
Unfortunately, it seems like there is still no value...
I want to add an external button that mimics the properties of the buttons in the nRF52 DK. I read that the switches are all active low, so I assume that this means they are...
Hi,
in peer_manager.h and id_manager.h the docs say a function can return
BLE_GAP_ERROR_WHITELIST_IN_USE
But the error code is called
BLE_ERROR_GAP_WHITELIST_IN_USE...
Hello,
I have an nRF52840 on a custom board. The nRF52840 has been pre-flashed with the Adafruit UF2 bootloader for early development exploration. As the project moves forward...
Using SDK15.3 and S140
following from my previous support request regarding TWI sleep current, I got the newer AIS2DW12 accelerometer and I have successfully connected...
Hello everyone!
I want to develop and app the sends some sensors data over BLE.
I am trying the peripheral_uart sample of the NRF Connect SDK but it seems that I cant...
Hi, there:
based on \\nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_uart\pca10040\s132, I need add justworks BLE secure connection.
Do you have any document...
Hello, I want to use Multiple Connection (Multiperipheral sample) to connect with multiple IOS phones at the same time to implement UART. Currently, up to 9 units are set...
