I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
This topic follows devzone.nordicsemi.com/.../why-having-nrf-connect---bluetooth-low-energy-open-makes-my-connection-faster-and-more-stable which was partially fixed (with...
Hello,
I would like to use Nordic SDK libraries (currently I'm using SDK 17.0.2) to read and write on a FM24CL16B I2C F-RAM.
This device has the following writing workflow...
Hello,
I recently used GPIOTE Events to manage Digital state changes and this is awesome. I would like to perform similar thing but when a PIN goes under/above a given voltage...
Hello,
I'm running NUS sample from NCS SDK 1.5.0 on two nRF52840 PCBs. Central board is Taiyo Yuden module and peripheral is nRF52840-DK. I've added some lines to prj.conf...
I am looking for an example where I can enable UARTE0 and UARTE1 on the nRF52833 DK. I am using nRF5_SDK_17.0.2 with Keil uVision V5. I am successful with the loopback example...
Hi,
I'm new to building circuits with Nordic devices and am unsure about how to connect the MC3672 accelerometer: https://mcubemems.com/wp-content/uploads/2020/03/EV3672AB...
Hello,
We have been working on Nordic nRF52-DK board.
Board can be reachable by Bluetooth in the first 10 minutes of power supply. However after 10 minutes, we can...
Hi everyone ! I am working at a project. I dont't know which mcu was used this project but it was written for pca10040 and used s132. Many values are write to flash memory...
I merged in some of my code to the examples/thread/dfu/client in the v4.1.0 SDK for Thread and Zigbee. After getting OTA DFU working, I moved onto some commissioning related...
Hi there,
i'm wondering if it's possible to get access from the demodulator directly within the nRF52? it shows in the block diagram below, is there any way to bypass...
Hello Nordic,
I'm trying to run nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_uart (PCA10056, S140 softdevice) with default sdk_config.h . The master is nRF Connect...
Hi,
I am new to nRF Connect SDK. I am trying to achieve over the air Firmware upgrade through nRF5340. The SDK i am using is nRF Connect SDK v1.5.0 .
As per my understanding...
