Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
software : nRF5_SDK_14.0.0_3bcc1f7
hardware :nrf52832qfaa
example : ble_app_hrs_rscs_relay
i want use "example : ble_app_hrs_rscs_relay" to receive more then 20 byte...
Hi all,
I have a DK 10056 rev 1.0.0, and it suddenly stopped working on the Embed side. Using the USB port (the DK one, not the NRF one), the LEDs (4 LEDs for testing purposes...
Hi,
I am using an nRF52 based chipset and programming the device with the hex file.This is being performed using the nRFConnect v.3.4.1 Programmer. The erase and write option...
Hi,
I have a custom prototype board based on nRF52833 which runs a working firmware and I have not any other prototype ready to hand.
Unfortunately, I think that the source...
Hello,
Considering the waveforms in the following chart, which will be the best approach to keep the power consumption as low as possible?
Specifically, which peripheral...
Best regards:
I have one PTX and one PRX, both nRF24L01+ with PA and LNA. PTX send 4 bytes to PRX but PRX doesn't get RX_DR, and PTX fire MAX_RT.
PRX:
PTX:
...
Hi
I had a strange error when I Set up a project in Segger, I got TRUSTED EXECUTION NONSECURE error.
I was trying to build the project for thingy:91 with nrf Connect SDK...
Good day;
I read the relevant posts. But I'm confused and do not understand.
1. What is the best way to identify the requesting device? Its specification identify is unique...
Hello
I want to set up the SEGGER Embedded Embedded Studio and I'm at the stage where I should select the board directory.
The Getting started Assistant shows an example...
Hi
in nRF9160, there are several AT commands to measure/handle battery voltage: examples:
%XVBAT
%XVBATLVL
Which PIN do they sense? are they VDD1 & VDD2 (which I believe...
Hi,
I am currently developing a health monitoring device. I would like to know if the nRF9160 is certified to be used with the LTE network in Canada. I am interested more...
Hi,
Recently we have bought nRF9160 DK PCA10090 devices and tried to add to nrf cloud account but we end up with issues.
Following the standard procedure mentioned in...
Hello,
I noticed that when my Thingy is charging the Temperature measured is 4°C higher
The data are coming from NRF Cloud.
We can clearly see the temperature rising...
I use SDK16.0.0 and SD7.0.1-S132 Implement NUS functions, 1 * ble_central and 6 * ble_peripheral. The uart of ble_central connect to STM32MCU. My system run as follows, 6...
