Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hi,
I have gone through the lfs file system from zephyr samples but I could not find any solid documentation for fs and spi flash drivers available.
I have written the...
Hello,
I want to use the PWM driver to change the output voltage with respect to analog input voltage. If I call the simple_playback_sequence from the SAADC event handler...
Good day. Some smartphones cannot connect to NRF52832 (SDK17): - iPhone XR - iPhone 11 Detection goes well, but smartphones cannot fully connect and freeze at the connection...
Hi Sir,
We tried to download the nwp_024 , and check the tape reel information of nRF5340.
But we could not find the nRF5340 lists in "table 2. Carrier tape dimensions...
Hey everyone,
I firstly want to preface this with my lack of credentials. I'm very new to embedded systems development and am figuring things out slowly so please bear with...
I want to initialize LFCLK on startup to reduce power consumption. I am doing it as given below. Is this the correct approach of initializing LFCLK to reduce power consumption...
Hi,
I am using nRF52840 as BLE peripheral, on a Zephyr application under NCS 1.4.2
I want to limit the connection interval to 7.5ms (min+max)
I can see that the only...
Hi Nordic DevTeam,
I am using nRF52840 (1MB Flash, 256kB RAM). I would like to store a log data to flash memory that I can extract them to my Android phone later on when...
Hi All,
I want to verfiy the current consumption of nRF52840. I'm using an nRF52840 DK and SDK 17.0.2 RTC example. below are the verfiy steps:
1. Cut SB40 on PCA10056...
Hi,
I we are developing project on BLE NRF52832 module and it warked correctly. during the debugging suddnely it stoped responging to programmer and couldn't be reprogrammed...
I have read about eddystone protocol. I have run
nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_eddystone\pca10040\s132\arm5_no_packs
i am able to build the code...
Hello
My setup looks like this. I am using nrf5_SDK_for_Mesh_v5.0.0 with nRF5_SDK_17.0.2. I have extended the sensor model example (in nrf5_SDK_for_Mesh_v5.0.0) and call...
