Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
SDK: v15 SoftDevice: S132 Chip: nRF52832 on BL652 Module
I have a command->response type system. The Central (Android phone) sends a command, and the Peripheral (nRF52 device...
Greetings!
I am using nRF52, SDK14.2, and NUS with MTU = 64. I want to transmit 1000 byte string over BLE upon reception of any character to "nus_data_handler" I have divided...
Hello. I'm just trying to get going with the nRF9160 DK which just arrived.
Using macOS.
Followed Getting Started and then nRF Connect Getting Started Assistant, and everything...
Hello,
I'm currently working on a project that requires data to be stored to an microSD. I'm using a custom board with the nRF52832 chipset and a Molex micro SD card holder...
We are working on a product with a pair of Central and Slave BLE devices that will be sold in pairs. The plan is to have the pairs preconfigured in factory so that the Central...
Hi,
I have an error to download firmware in nRF52840-DK, from output console show it failed at verification on address 0x00000000.
I try to compile the light switch example...
Hello,
I have a total of three nRF9160 DKs. Two are version 0.8.2 and one is version 0.70. The version 0.8.2 DKs only work with iBasis SIMs. When I attempt to use a different...
We are using nRF52840 with sdk 15.0 version & segger embedded studio. We are able to store some small amount of configuration data into flash using FDS. But now we want to...
Good afternoon,
I have been having issues discovering any service within a peer device which i have recently paired with. I am using Nordic SDK 15.2 and softdevice 6.1 on...
Hi,
let's say fds storage doesn't have enough space, but it can be freed by running garbage collector. Now, new peer connects and initiates bonding procedure. My questions...
Hi all I am developing the beaconing example form nrf52832 nrf sdk mesh3.1 I compile the code and run but I don't find document on provisioning the beacon.
Other question...
I have a ble server with display developed for passkey security. It works fine when the Master (i.e. client) is set to have Keyboard input capability, which is good.
The...
Hello,
I am using nrf52832 development board. I am using segger tool. In example -> ble_uart , i am sending some 100kb of data to UART using BLE. I want to controle the...
without bootloader, nordic can work?
i get two nordic board,it work well.but when i read the flash layout
i found that the two board only have softdevice and application...
