Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
Hi,
the pull-up resistance Rpu of GPIO pins as stated in Product Specification v3.1 in Table 62 is supposed to be 13 kOhm (typ). Since we measured a different value on pin...
I started development with the S132 (SDK 15.0.0) peripheral example "blinky". After some modification, it handles all necessary communication with my phone flawlessly. Now...
I'm attempting to use the USB MSC example (from nRF5 SDK v15.0.0) with external flash chip replaced with Winbond W25Q128FV and I see the following logs:
[00:00:00.000,000...
Hi,
I have designed a customized for nrf52832 with a trace antenna. I haven't used any low pass filter and made the changes inside sdkconfig.h file to use RC and that board...
Hi,
I'm using nrf51822 module purchased from www.waveshare.com/core51822.htm . I'm running uart over ble application example. I commented uart_init() function in main(...
Hi,
I have the following setting. I have a dongle with with a nrf52 which sensd all data received from the NUS service to the host via a uart and a FTDI. The FTDI is capable...
Hi.
I want to implement multirole on the nRF52832. I want to advertise beacon data while scanning. So, I modified ble_app_uart_c in the ble_central example. Below is a description...
Hello,
I would like to disable and enable the nus_data_handler in my code to work with several interrupts, so I need to disable that handler and then reenable that again...
hi,
I am using nRF51-DK board as external programmer to program Minewtech Minibeacon having nRF51822 chipset (QFABC1, 128KB flash and 16KB RAM).
Tools:
SDK: nRF51_SDK_10...
Hello, Is it possible to use a RedBear V2 with the DAPlink as a Bluetooth dongle, apparently, the DAPlink can function as a USB-UART bridge. I'm new to SoC and am trying to...
Hi
I am trying to load my shiny new NRF52840 dongle with a simple blinky app using the nRF Connect (v2.4.0) but I get an error stating that the 'Region starting from 0x0...
Hi,
I follow exactly the same as "Interactive mesh provisioning and configuration" and stuck at "Adding a Light Switch client (optional)" part.
Everything looks fine,...
I am working on a J-link command line.
i just want to lock a device after a write a binary file into device.
In j-link there will be option for a unlock a device like...
Hello,
I'm developing a program using nrf52832 DK and SDK V15.
I want to activate the SPI transmission when NRF_RADIO->EVENTS_END occurs using the PPI. I follow the PPI...
