E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Hi,
There is much talking about the "large data transfer" over BLE, the l2cap channel being the best option for the moment.
However, does anyone know the datarate achievable...
NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Hi guys,
I am using the gcc setup to program my boards. However for flashing the softdevice I use nrfgoStudio. SO I downloaded the hex file and fashed the siftdevice. But...
I built the secure bootloader UART project without changing anything and I cannot program it using nRFgo Studio. It says:
This hex file has data in SoftDevice region. Try...
Hello,
I'm trying to use the Arduino BNO055 shield with PCA10040. This should be quite easy....but it doesn't work: I can't get any acknoledgement. Arduino use 5V pins,...
Hello,
I habe got a nRF52840-Development Kit. It is Herdware Revision 1.0.0.
While going through the Getting Started i find that the LEDs do not flash and that i have...
Just a heads up for anyone who bumps into this and is scratching their head. If you have ninja version 1.9.0 installed your build may hit an error with messages like this...
Hi everybody,
we have a remote control based on the nRF52832 and are experiencing a wierd issue with notifications.
We are using a custom 6 byte payload keymap characteristic...
Hi all, I use NRF52832.
I have a problem. I want when I connect to my chip and bond. After bond success, I insert new service. And when I disconnect from my chip, new service...
On page 69 of nRF52840 Product Specification 1.0 4413_417 v1.0 / 2018-03-16:
The table in section 5.3.6.8 shows that the WDT is NOT reset from a Wakeup from System OFF mode...
Hello,
We have an application based on ble_app_blinky that is actively scanning for advertised packets but does not attempt to connect. We have a second application based...
Hello,
i am using nrf52832. i am using 8 different pin as a 8-bit parallel port.
in my process i have to read each bit from each pin then converting those bit into byte...
I am using an nRF52840 DK. The software I have in it is emulating an NFC Type2 tag and is implementing a BLE peripheral.
When the device starts up everything works as expected...
Good day!
In SDK 12 I read values using this code:
and handle value in ble_evt_handler:
This works fine, but using SDK 15 this code crashes with fatal error...
This application uses a Rigado nRF52840 module to collect SPI data from 2 peripherals in slave mode. I have been unable to get the SPIS example running in the target board...
Hi,
This is a really weird problem.
======================
Setup of 52832 hardware:
- Custom board, using 32MHz XTAL and LF RC.
- SDK15.2, S132 610
- Segger RTT...
