Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
I'm using JLinkExe ( J link commander ) for Linux to flash the application firmware on NRF51822_QF_AA target. The following have worked so far, but I'd like to confirm and...
Hi,
I am upgrading to SDK 11.0.0 and S130 v2.0.0 from SDK 9.0.0 and S130 1.0.0 and I am stuck with an error when I call sd_ble_gap_adv_start. Here's the code that now fails...
I have the following two lines with pin 21 not connected to anything:
nrf_gpio_cfg_input(21, NRF_GPIO_PIN_PULLUP);
uint32_t value = nrf_gpio_pin_read(21);
I would...
Hello!
I'm trying to flash my SeeedStudio Tiny BLE board (nRF51822 QFAA) with SoftDevice S110 using Keil but it doesn't look like it's going to let me. I'm just getting...
Hi,
i am having some trouble getting my nRF52 DK (S132) to read a value provided by the nRF51 dongle(S130).
First of all, i am very new to this whole Bluetooth thing so...
Hello!
I'm trying to read 16 bit ADC Value on nRF Master app instead of only 8 bit, and I know that there is the example code on github which is only send me the 8 bit...
We have a new daughter board connected via I2C to an Atmel controller. What we need to do is load the right softstack onto the NRF and then send the needed commands to tell...
Hi Guys,
We have schematic of future NRF 51822 project, who can help us with PCB design? Or who can suggest me where i can do it?
PCB.DXF
schematic.pdf
Hello All,
I am trying to build a BLE peripheral project with RTX OS which is using S110 Soft Device and bootloader is also there in Flash memory region. So when I am trying...
I am just beginning to develop with BLE.I came across the nRFgo Studio through Nordic and BDS through the bluetooth SIG.
1]What are similarities/differences between the...
Hi.
I want to active HW timer with SoftDevice 7.1.0 .
Timer operation is good but I can not stop the timer.
The power consumption is 200~300uA after timer expired ( or...
Hi,
We would like to use NRF52832 chipset for our project, and we need to configure 11 pins as GPIO interupt , Is this possible ? How many pins we can have as interrupt...
