Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Hi,
There is much talking about the "large data transfer" over BLE, the l2cap channel being the best option for the moment.
However, does anyone know the datarate achievable...
NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
I'm using the nrf51822 TWI library. I've tried both twi hardware and software master library files and see the same behavior when using both (as a side note an explanation...
Am I right in thinking that the button handler only causes an event for a button press(although I realize it is possible to configure the button such that a release is interpreted...
Hi,
I have a Question regarding one project in which 1 NRF24L01+ Module transmit to multiple devices at the same time ? How we can configure for multi transmit ? like Tranmitting...
Dear Nordic,
The guys at ARM have this community around mbed which looks great. I would like to use it, but before I do, I would like to check if their use of your (source...
Hello,
I'm trying to understand how the ble_app_hids_keyboard example works. So far, I have hooked up a few more buttons to the board and can type hello.
Now, I would...
Hi all,
In my project I'd like to use gazell for to communicate 2-6 devices with host.
Furthermore I use switching between BLE and Gazell (only 1 device support till now...
I am trying to port an application from MBED LPC1768 to a nRF51822 Evaluation board to develop a multi-function application for the nRF51822. The BLE part (developed on the...
I am hoping to develop a device that works as a remote control for a smart phone app. There will be at least 5 buttons, and as the button presses will be infrequent, I am...
Hi
How to start and stop scanning continuously in android devices ?.I found that In Nrf master control panel android app there is an option of performing scanning such...
Hi,
I downloaded and installed latest master control panel for Win7. It now crashes when communicating with nrf51 dongle. Seemed like it crashed the first time while it...
I'm using the APP_BUTTON_INIT-Function to register a button at the GPIOTE-System. This works great while running normally, e.g. I can react on debounced button_down or button_release...
Hi
I am developing for the nRF51822 a 4 layer print with a power and a ground plane in the inner layers. I will be using a balun from Johanson Technology (2450BM14E0003...
I've heard that's not allowed. If so, why?
If it is allowed, are there any precautionary steps I need to take, not to interfere with the radio?
Thank you!
Gil
...
Hello, we have a custom board based on the CEAA WLCSP reference schematic with internal LDO setup. Our supply voltage is 1.8V (VCC_nRF). Unfortunately we don't see any BLE...
