We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Can you provide documentation of the energy costs for creating/verifying ed25519 and NIST P-256 signatures with the CryptoCell CC310 peripheral found on the nRF52840 device...
I am trying to set pins when I press a button, and clear is as soon as I stop pressing the button, however the board turns on all leds at once and does not respond to input...
I came across this old thread, which asks the same question, but was abandoned by the OP ( ) without follow-up:
https://devzone.nordicsemi.com/f/nordic-q-a/26699/52832-saadc...
Hello,
I am looking into migrating DFU and Bootloader over BLE from SDK v15.0 to SDK v15.3. I have a few questions about the code changes which I was hoping I could get...
I was reading about Mesh DFU and noticed that when it happens, the receiving node will rebroadcast it to all devices within radio range. It seems like devices will pick up...
Hello all,
I am trying to adjust the current consumption of my device based on nrf51822 s130.
A have read the https://developer.apple.com/hardwaredrivers/BluetoothDesignGuidelines...
I wrote some user data to 3rd party nrf52840 boards flash using the command "nrfjprog --memwr 0x1001084 --val 0x33333333" , when I ran the program the data values was not...
Hello,
I want to test the mesh provisioning demo with the codes provided on the GitHub:
https://github.com/NordicPlayground/thingy52-mesh-provisioning-demo
I have encountered...
We are using an NRF52840. After initializing a UART that uses P0.06-TX and P0.07-RX the following function calls fail: sd_ble_gap_device_name_set() and nrf_sdh_enable_rquest...
I am playing with the TIMER peripheral and I am seeing that I must call the function "nrf_timer_event_clear" in order to get the TIMER interrupt to stop firing once a COMPARE_EVENT...
As shown in subject, I tried to register many BLE services, DIS, BAS, HTS, and Custom Service. Then nRF52832(and nrf52840 preview) has stopped by an error of NRF_ERROR_NO_MEM...
I am working in nrf52840 sleep mode and it is working perfectly in system_off() mode, but while trying to wakeup from sleep using timer the device is not waking up because...
I am configuring the SAADC for Single-ended mode which I would think is a simple/common task, but my output from the ADC is very jittery. It seems to jump between a good reading...
Hi!
SDK15, s132, SD6.0.0, nRF52832
I have nRF52832 in central mode and some bonded HID devices and another nRF52832 peripherial devices.
Now in the my central nRF52832...
