Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
I'm using this code to log the BLE MAC address on my peripheral device, an nRF51822.
void ble_log_mac_address(void)
{
// Log our BLE address (6 bytes).
ble_gap_addr_t...
Hi,
I'm basing my project on ble_hrs_freertos example project (nRF52832, SDK14.2, PCA10040)
When calling assert(condition) in the original example project, it works...
Hi!
We are evaluating the 52832 soc for use with a DALI-controller. The communication speed with the controller is at 1200 baud, Manchester encoded. Is it possible to interface...
In BLE communication, I want to send 244 bytes of data from the peripheral to the central every 50 ms, is it possible? If possible, please tell me the setting method.
Hello, I have a problem with the configuration of GPIOTE low accuracy pin interrupts. My code is running on nRF52832 and already uses ble stack, PWM1 and PWM2 instances with...
Hi,
Right now I have a program on nRF52-DK (SDK 11) that scans for BLE adv packets, and transfers data from some specific addresses to PC through UART. Around every 10ms...
I'm attempting to use the PPK with the nRF52840 PDK with no success. I'm getting nothing running the nRF Connect with the Power Profiler. Configuration is as follows:
nRF52840...
Hey Guys,
Have been playing around with various MTU sizes to better understand throughput. I'm curious about one scenario though. Let's say for example that we are using...
Hi
We are using a slightly modified (but fully compatible signed bootloader) in out product. On the application side we have a C# implementation of the DFU protocol that...
Hello there,
In my next project I need a data link similar to BLE classic (like the HC-05 module) and it needs to respond with an app API fast and push data rather then...
Hi,
I'm following "ble_app_uart_c" example and works very well with SDK 10.0.0. So now I want to communicate with HM-10 module, but this has one Tx/Rx Characteristic. Are...
Hello,
In my quest to monitor the activity of hundreds of nodes (directly addressable), I am facing quite an obstacle.
The small memory of the nrf52 (nice piece of hardware...
Hello How do I remove one server from mesh network? The client needs to recognize like a new device. I did try to use these functions without success on a event: nrf_mesh_node_config_clear...
I have successfully connected BT832 Module to NRF DK. I have erased BT832 and Falsh s132_nrf52_5.0.0_softdevice.Hex. using nRFgo Studio without any issues.
I have copy pasted...
