We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
I'm trying to program 500 raw (not populated on boards) Taiyo Yuden EYSGJNZWY modules, which uses the nRF51882 chipset.
Does anybody know where I can get a fixture to do...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
Long story short, I need to create a packed struct.
I knew the pragma way, to change aligment, didn't work.
I looked up and found the __packed (I'm using Keil µVision...
Hi,
I am planning two have the following network:
1 central communicating with 3 peripherals
One of the peripherals will be a smart device (iOS or Android). What...
Using SDK 12.2, I have compiled the secure bootloader successfully, tweaking the sdk_config and Makefile to use RTT for logging and turning on logging, and using the "_debug...
Configuration: Nordic PPK, PCA10040, PC10028 & PCA63511. Current consumption is relatively high on nRF52 vs nRF51; nRF51 is configured with SDK 10.0 and nRF52 with SDK 12...
Hi,
I have got my nRF52 DK. I could flash softdevice using nrfjprog.
But after reading s132 specification, i have following doubts.
How to flash application from the...
Hi all --
I have an application where I have a LDO generating 2.6V from a single lithium-ion cell. It has an EN input that I want to expose to the nRF52 with a little RC...
Hi,
I'm searching for the nRF52 Ref Manual. I've located the Product specification for the nRF52832, but can't seem to find anything for the Reference Manual.
I found...
To maintain compatibility with our current systems we would like to be force characteristics to be at certain handles, rather than having the soft device assign them sequentially...
I am upgrading from v12.0 to 12.2. I am using Linux, Eclipse, GNU ARM and Eclipse managed make.
I get compiler error ...nrfsdk12.2/components/drivers_nrf/hal/nrf_gpio.h...
Device: PTR5528
Board: custom.
I have just given coin battery directly to VDD. At P0.00, P0.02 i have two leds. On p0.03 and 05 i am having one interrupt and other is...
Hello everyone.
I am currently working on a device with some peripherals.
I have SPI slaves and other sensors that I am monitoring using GPIOTE driver.
I noticed a...
I am attempting to implement buttonless DFU with my application.
Using SDK v12.2.0 on a Rigado BMD-300 module (nRF52832)
Starting one step at a time, using nRFgo Studio...
