I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
Hi,
I'm developing a unit which i need from time to time to send a packet throw I/O lines (F.E.virtual uart)
However the packet bit timing is very critical.
As far as...
Hi, I am using nrf52832 with SDK 12.3.0 and nrf 52 dev board. I am experiencing a problem whenever I programmed nrf 52832 using nrf52 dev board and NRFGO, after certain number...
Hello, I'm currently using the nRF51DK with Wireshark as a BLE advertisement sniffer. So far this setup has worked great, but I'd like to make a small modification for development...
Hi all,
i am currently working on 5 nrf52832 DK boards, i want to use nrf mesh for indoor positioning system. I am currently using nrf sdk v15.0.0 and nrf mesh v2.2.0. ...
Hi.
We are on early phases of getting UART DFU support for our product. However I seem to run into communication issue with the bootloader even with the examples provided...
Should the DEBUG compiler flag be removed before flashing a board that should enter sd_power_system_off? I've seen some troubleshooting guides mention that Debug mode can...
I have set up the thread border router. I connected the NCP (a nrf52840) with a usb cable to a raspberry pi. Now I wonder if it is possible to connect the raspberry pi with...
Hi all,
Currently, I am working on Nrf52 DK with nRF52832 on Keil IDE. My focus is MQTT with 2 nRF52s and RPi. I have succesfully used examples in SDK, but now I am trying...
Hello,
I have got new rigado-301-A-R module, I want to know following things as I want to work on linux and i have a custom board just like rigado 301 eval board.
1. Procedure...
I have an embedded platform running JerryScript. Now, I need to add BLE functionality to it. The BLE module (connectivity chip) will be used is nRF52840. For this, I guess...
I’m trying to program a custom board with nrfjprog, but cannot get it connected correctly. (Connection is standard SEGGER cable, segger mini edu)
nrfjprog -f NRF52 --halt...
hi ，i have a problem! how to slow down the update speed when bootloader receiving the pack. my project is base on the SDK 15.2.0,s112 ,secure_bootloader example ,nRF52810
Dear nordic,
i want to create a low power current consumption ADC. i don't need adc value in every time. my need is just take adc value and disable it.
whenever i want...
HI,
I'm currently working with two chips RF24L01+.
Each chip switch in sending role to receiving role several times. By default, I set them in sending role and I whait...
I use sdk15.2 and nrf52832.
I copy i2s examples to nRF5_SDK_15.2.0_9412b96\examples\ble_peripheral\ ble_app_hrs ,and nRF5_SDK_15.2.0_9412b96\examples\ble_peripheral\ ble_app_hrs_freertos...
