Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
I tried to add a chip of our own design to NCS, but when I tried to write the device description file, I ran into two problems:
1.Even if the chip description file is compiled...
Hi,
I'm using the example project usbd_msc and I am having no luck having the volume come up on windows when I plug in the nRF_USB line. I can see "nRF52 USB MSC Demo...
We are currently getting our firmware ready to test devices for FCC and other radio testing. We have an AThost-like setup that passes AT commands from a terminal over a BLE...
.Hi Nordic Support team,
I'm using NRF52832, SoftDevice S132, SDK version is nRF5_SDK_17.1.0_ddde560.
I want to transmit 9 bytes of data collected from an I2C sensor...
Hi,
the I2C burst write function below work perfectly <16 number of bytes. Once I transfer more that this, the return code throws an error "-28" and my scope doesnt even...
Hello, I would like to develop an automated tool for our production line to use to perform DFU on our nRF52832 system. Is it possible to communicate with the nRF52 Dev kit...
Hi, I developed a custom board and I am able to toggle other IO pins but somehow pin 10, 9 wasn't working. After some research, I found that NFC must be disabled to make it...
Hi,
I am trying to set EDRx en LOG_INF the result using following code:
static struct lte_lc_edrx_cfg drx_cfg ;
//enable EDRx
LOG_INF("== Setting EDRx =...
Hi,
I have a custom board with a nRF52840 and the nRF21540 FEM. To control my FEM, I have added the following to my code to my nRF52840_nRF52840.dts file:
/ {
nrf_radio_fem...
Hello Everyone. I tried to run the ble_app_multirole_lesc example on SDK 16.0.0 to test the numeric comparison match feature on bonding. And found that the handling of this...
Hello,
I am currently updating from SDK v2.3.0 to v2.5.2 but I am not able to get the 'psa' functions working correctly (as they did with previous SDKs).
I am trying to...
Hi, How to find out what function is being called, when sw interrupt occurs? I have created a timer that should call a function. But I'm having a hard time finding what function...
Hi,
I am working on custom board which has nrf9160 as modem and stm32 as host controller.
here I am used lwip stack on stm32 controller to get the IP address.
I have...
I'm trying to integrate AES-128 (ECB mode) decryption into my project
I've based it on the AES_CBC sample, and adapted it to use ECB mode instead of CBC. When I compile...
Trying to use the nRF Connect quick start with the evaluation board and the programming fails. 2024-05-22T09:09:27.145Z INFO Initialising nrfutil module: device 2024-05-22T09...
