Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
We are writing SPI drivers for RF chip and blocked on the below issue. The issue we are facing is the Chip Select line is not active(active low) until the TX transaction is...
SDK: 12.3.0
SOFTDEVICE: s130_nrf51_2.0.1_softdevice
CHIP: nrf51822 AC 256K flash 32K ram
GCC flags:
# C flags common to all targets
CFLAGS += -DBOARD_CUSTOM
CFLAGS...
Hi,
I want to write or change the code in to nRF52832
I have some code this code i should write for nRF52832
kindly give any suggestion
here is the my code
uint8_t...
Hi everyone ,
I have a custom PCB using nrf52840 and i measured the current consumption using PPK(power profiler kit) . The sleep current value that it show is 4.5mA.
...
Hello,
I want that two devices can connect with each other and only each other . To do this i wanted to use whitelist on peripheral side but i found that i could use filtering...
Hello.
I'm using nRF SDK 15.2 together with the Nordic 802.15.4 driver ( here ).
When trying to add the libuarte module to my project I started having mysterious issues...
Hi there,
I'm trying to get a one button nrf52832 device to behave like the following:
1. Button press short: RESET or WAKE (depending on POWER state)
2. Button press...
Hello,
I got problem when I press button program go to interrupt mode, but than all stops because of vektor catch. Im using ble_app_uart example.
Here is my main function...
I guys, I m trying to use the nrf52840 protocol in order to send an interrupts between two boards.
Looking at the examples provided in the SDK i didn't understand how to...
Hi, I have a particular issue that happens intermittently, I was hoping someone here has come across the same issue and possibly knows how to fix it.
My Setup:
Using...
Hi
I am trying to add manuf data to ble_app_hts sample advertisement but without success:
static void advertising_init(void) { ret_code_t err_code; ble_advertising_init_t...
nrf52840 last version of SDK Hello I need help. I want to start ble_adv and then stop with a button signal and start again with another button signal. The idea is
Loop:...
Hi,
I am using ble_app_uart example and want to detect the read evant/ call back. Kindly help me how to register a call back function of a read type characteristic. I want...
Hi all, I'm working on nrf52832 in segger embedded studio. Using ble scanner app, I'm entering some random values. So when i enter a value, I'm adding them to watch and checking...
