Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
What is the input impedance or input current of port P0_30/AIN6 when operating as an ADC input? Nominal or typical figures would be OK, but maximum and minimum figures would...
1、Nrf52810 does not have VDD_PA pin, whether it needs software control, whether any pin can be replaced？
2、Is there an example of the use of PA/LNA circuits in gazell and...
Hello,
The Gazell Pairing User Guide in the infocenter states that the AES ECB block is used for encryption & decryption. However, the product specification document for...
I have an issue with bonding between a PCA10040 running the sample Glucose app and an Acer tablet running Android 7 and nRF Toolbox. I have not seen the problem on a second...
Hello sir,
I am a beginner on NRF52840. I am using Nrfx_spim example for interfacing sensor with NRF Board.
I have done some driver about Reg_read and Reg_write. I tried...
I'm using the basic sdk example of ble_app_hrs_freertos example and created two tasks in it, namely Task1 and Task2. Now I have enabled preemption by setting "configUSE_PREEMPTION...
Hello everyone,
I write datas from my Client to my Server, but I don't really understand where I can retrieve my data on my server.
Is this function allowing to get...
Hi ,
What we want is a accurate ms.
below is what we do 1. Set the prescaler config.prescaler = 31;
2.When I need the Elapsed ms, First ,I get the elapsed rtc counter...
Hello everybody!
All boards below below have nRF52832 chips.
My task now is to develop a set of applications that will support the following scenario:
1) A person...
This question comes from my high-level goal of testing I2C using the SWDIO/SWDCLK pins on the nRF52840 Dongle, so if there are faster ways to experiment with that functionality...
Hi,
I am having hard time understanding the use of "addr_id_peer:1" field in the structure ble_gap_addr_t. Could you please help me understand the usage/significance of...
Hello, Is there any intention to add the the nRF52810 reference design to the Eagle library on github? There are five Eagle design blocks already available on github, except...
Hi,
I encounter error when I debug the nrf52832 DK.
I run the example code "ble_app_uart" provided in the SDK.
Below error shown when I set the break point in any line...
Hi,
I am using an NRF52832 on a custom board and I programmed the Broadcast RX code into the board. I use ANTware as the master with a channel period of 4 and send broadcast...
