Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hello,
I'm trying to setup a gazell application that could use the same resources of the Nordic SD.
Using the keil package manager, I switched the package configuration...
I'm going to configure nRF51822 chip as a spi slave.
And there are no more pins for the connector.
So I am trying to connect SS pin to the ground pin, instead to connect...
Hello
I'd like to write my own application for flashing nrf51822. It will add some additional information info hex file.
How can I burn hex file into the flash using...
Hi,
I was wondering if you can please clarify the licensing terms for the nrf51 softdevices?
I found the link to the SDK license here:
devzone.nordicsemi.com/.../license...
Hi,
I am trying to use GCC with Eclipse as explained in this tutorial , and after spending hours trying to figure it out, I am completely lost and ask for advices and help...
Hello,
It appears that changes were made to the DFU bootloader project in SD 8.1. The project no longer seems to function when using GCC.
I am using GCC 4.9.3
when...
I'm following these instructions. And downloading a project from this github repository.
The downloaded github zip file contains the following folder "ble_app_uart_c_S120...
Hello,
I use this program.I take values.Android Application want to show the values.
Program:
#include "ADXL345.h"
ADXL345 accelerometer(p5, p6, p7, p8);
Serial pc...
Hi all,
I would like to use the Arduino programming environment on my nRF51422 prototype. I have seen that RedBearLab has done the migration for the nRF51822 which quite...
Is the nrf52832 developer kit compatible with Arduino Leonardo? I know that most Arduino shields work well with Leonardo, but a few have troubles.
Thanks
Hi,
I would like to have a recommended supplier for the 32MHz crystal. I have seen the specification for the crystal. But from my experience it is a bit more complex than...
I followed the guide of this and when I opened the project " BLE_Gateway" ,it showed that the "spi_slave.c","softdevice_handle.c"and "ble_advdata.c" file couldn't be found...
I can not compile the example project 'ble_app_uart_s132_pca10036' ,in nRF52_SDK_0.9.2_dbc28c9\examples\ble_peripheral\ble_app_uart\pca10036\s132\arm5_no_packs.the error given...
