Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
This thread mentions having the master read the DFU Revision Characteristic to determine the DFU revision. I've based my DFU and application off the dfu_dual_bank_ble_310_pca10028...
Could you estimate the free space for Application on nRF51 and mRF52, on this case for Homekit with FOTA :
Boot Loadeer with FOTA
Homekit Enable
BLE Software Device...
What are the options to update firmware (Application/Bootloader/Softdevices) for multiple devices built on NRF51x22 ?
Using Master Control Panel could take days programming...
Dear Nordic Team,
I am using HID mouse example code in my nordic dk board.
I can able implemented fallowing logic in my code to do left , right and middle button click...
Hi,
I am using nRF51422 with SDK 9.0 and SoftDevice130 with nus service. I have a custom android app running on BLE uart service. Data communication and connection handling...
How to save the uart app on my nrf51dk board? it only runs when i connect it with the usb. another question nrf51dk have a nrf51822 chip(SoC)?
please help me out. i want...
Hi,
I have installed EmBlocks 3.2 (the last one) but only extremely simple examples will compile.
It appears that the support files in wizard/arm/nordic/nordic.zip/Common...
I have been struggling with the custom characteristic implementation. I have followed the great tutorial on custom service that is online but there is really no doc or information...
The nRF Beacons iPhone or Android app requires adding a new beacon devices in order to notified events. Is it a must for beacons? Or is it just a one step for examples. In...
I try to advertise with a custom UUID and I do not know how to do it.
The standard services works with 16 bits and I need to work with 128 bits
So how can I do it?
Thanks...
Dear Nordic family,
I am using Bluetooth Low Energy, Beacon module with ARM Core from Tindie ( Product link ). The reference manual from their website is attached IMM-NRF51822_RefMan...
I am trying to work on ble_app_uart example project working.
I am able to see that the "nus_data_handler" is triggered when any data is received over the BLE channel. On...
[Duplicate question. See the original post here ]
Dear Nordic team,
I have purchased Bluetooth Low Energy, Beacon module with ARM Core from Tindie
They gave me...
Hi,
Im trying to send data via the NUS service which is larger than 20 bytes. I understand that I have to break down the data into chunks in this case, which is what I...
I am new to embedded programming.
I use JLINKEXE (on Mac) to load the S110 softdevice and my application. When I am in the debugger, the app loads and all runs as expected...
