I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hello-
I recently got a custom board made with a nrf9160 module and am having trouble programming it. This project was reviewed by your team (private case ID: 321889) and...
Hi,
In NCS 2.0, the ability to add a custom child image was added. This works fine but as soon as you include the mcuboot child image, the order of the child image builds...
Hi, I have an issue I can't understand. I'm getting the TRICKLETIMEOUT (Trickle timer timeout) ERROR 64 from my nPM1300.
If I understand correctly:
1. Trickle charging...
Hello,
My company has developed a Bluetooth application that runs on the nRF52832 and we are about to perform FCC pre-scan testing next week. In order to prepare for this...
Hello everyone,
I am having trouble using the bt_nus_shell.py script and a NRF52840 development board to send shell commands. I am trying to follow the instructions mentioned...
I'm running into this issue quite often where I have a Build failure. I'm sure to others the way to troubleshoot what the issue is may be obvious, but being fairly new to...
Hello,
I am currently migrating from NCS 2.6.0 to NCS 2.7.0 on my board with an NRF9160.
During that process I switched to the new hardware model and to sysbuild. As far...
this is the last log message from monitor thread, I never got any error message from the thread.
00 > [ 01:37:03.890 , 808 ] <dbg> monitor: print_die_temperature: CPU...
i Used a nrf52840 DK board and zephyr sdk v2.6.0. I'm start the ble advertisement and configure the gpio interrupt on sw1 in low mode flag GPIO_INT_LEVEL_INACTIVE (Low level...
Hi.
I have following error:
Here is my prj.conf :
I would like to avoid using CONFIG_SHARED_INTERRUPTS.
Only GPIOTE0 is on IRQ number 11 so I couldn...
Hello,
I have had this issue from the first time I installed VS Code and the nRF Connect Extension.
When I open my project, the connected devices pane is just missing...
Hi!
SDK Version: v2.6.0
I am getting build errors when trying to use PWM for an RGB LED. I have followed guides provided by Nordic but I must be getting something wrong...
Hi,
I am hoping to send/receive binary data (a protocol) on the same UART that has logging/shell enabled. Is there a way to access the UART RX traffic that the shell gets...
Hello, I'm using nRF52840 and nRF_SDK_17.1.0 to build application and bootloader (slightly modified example) both using Soft Device. Due to size and time constrains of system...
I am new to the nRF52840 and the whole Nordic environment, so this may be a pretty basic question. I couldn't find any other blog entries that fit.
I am developing a manufacturing...