Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Dear DevZone Team,
I'm facing a very strange issue whereby the sample code from the Lesson2_Exercise2 of the Wifi Fundamentals course does not allow my development kit...
I currently use 8 nRF52832 as PTX and 1 nRF52832 as PRX. To ensure better communication quality, I wrote the code for PIPE allocation. The channel is assigned by PIPE 0 as...
Hi,
I'm working on a custom board with an nRF52840 MCU and a MAX17260 fuel gauge IC interfaced via I2C. The goal is to read the voltage of a battery using the MAX17260....
Dear all.
I have one question about thread certification environment:
I want to setup internal test environment only with Nordic nRF52840(no other bed devices). In the...
Hello,
In an existing device using the nRF52832 I have 2 SPI Master instances. Please, may you confirm that is possible to create a third SPI Master instance?
By the way...
Hi,
I am working on project, in which we using nordic nRF52840 chip. We need to flash the app+SD+BL image file in external QSPI memory.
After prevalidation, the DFU controller...
I'm having a problem using SPI within Zephyr. My custom nRF52840 board has 74HC959 shift registers to drive LEDs. I'm using the SPI bus to transfer LED on/off states and can...
After clicking on ACTIVATE SIM and having correctly filled in the SIM IICD and PUNK I am receiving the following message: Request failed with status code 503 What does this...
Hello,
Using scan sample I am trying to read drone Remote-ID. When broadcasting Remote ID via Wi-fi Beacon no problems occur, but once selecting only Wi-Fi NAN as delivery...
Hey! I'm working on a LE Audio project utilizing the nRF5340, where I need to stream audio both from and to the nRF and I have encountered the error "sw_codec_lc3: LC3 enc_bitrate...
Hello,
I can see there are some ADC examples on Github https://github.com/NordicPlayground/nRF52-ADC-examples But those examples are nRF SDK5. Are there any ADC examples...
Hello everyone,
I have a problem using pstorage_update. Normally it does as it should, but once i call ble_stack_init(); on my code, pstorage_update doesn't work anymore...
Hey,
I am trying to use the example for Sync_Advertising_conn to get a connection between 2 nrf5340 devices. but I get this message
the problem is in the config
CONFIG_BT_PER_ADV_SYNC_RSP...
Hello,
I am using the nRF52811 on a keyfob that transmits short packets when a button is pressed. The button directly connects power to the MCU, and the firmware immediately...
