after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I have followed the instructions in nRF Connect 3.3.0 - getting started assistant to setup my nRF connect SDK.
I proceed to set the nrf repo to v1.1.0 branch (last stable...
Hi, I Implement void WriteRegister and ReadRegister SPI interface with mfrc532 but some time right,some time wrong.
Some time i write value in a regsister and i read again...
Hello,
I am emulating the behaviour of a device doing this operations (Using pc-ble-driver-py 0.14.0 and nrf52840 dongle):
Is connected by a smartphone app
Exchanged...
Hi,
I'm using PCA10040 board and J-Flash to program a HEX file. However, the programming failed because of the license problem. How can I solve this problem?
Thank you...
Hello. I want to create a profile here so that I can ask private technical questions. You ask for personal info like full name, phone, address, etc. Is any of this information...
Edit: The problem was caused by me. Solution is in replies.
I was testing read back protection functionality. For one device I've set protection using openOCD by setting...
Hi,
I noticed nrfx_spim.h contains a method called `nrfx_spim_xfer_dcx` but I can't use it directly in my SPIM app.
I am wondering if that method is available to nRF52...
Hello,
I did getting started guide on a new computer (Windows 10 64 bits) and when I tried to check if all is ok with AssetTracker, I got that error message. What cna I...
We are currently getting intermittent errors in our ANT enabled application in field testing. To try to understand where this is happening I want to send over ANT an indication...
Hi ...
I want to measure the temperature using thermistor .. I am working on saadc example . I need give the reference voltage as 5v how to give that ? is there configuration...
We are developping an application using an NRF52840, Based on nRF5 SDK for Thread and Zigbee V3.0.0
Running S140 softdevice
One way of doing OTA is described here (Thread...
Hi,
We need to program nRF5x IC, so for that we are trying to program in the DK boards. For this we are using nRF52840 dk board and nRF51822 dk board (where nRF51822 IC...
Hello.
I try to provision Thingy52 in according with this document.
Can someone help me to create aray byte of invitation please?
In this case we have: Transaction...
