Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi Nordic Team,
What I want to achieve is to add a service with a custom 128-bit UUID that has about 4 characteristics with a completely different 128-bit UUIDs that are...
Hi Nordic,
I'm using NRF52832 to design a producation that needs four SPI interfaces.
The four spi peripherals are: gSensor, LCD, SPI Nor Flash, and PPG Sensor. Now...
Hi,
I'm working on a custom board with the nrf52840 engineering version n52840QIAABB with de SDK15. I've tried the exemple usbd_ble_uart from the SDK15 and it works well...
Figure 1. Data encoded and sent (attached)
Figure 2. Screen shot of wrong Time data (attached)
Here is some code that seems to be correct, sending 10 bytes that look...
Hi ,
I want to know how to give passkey to nrf8001 peripheral mode if it dont have display/keyboard/button, I have hear about justworks but not sure how it will work. Could...
Hello,
I am was playing around a bit with the twi_scanner-example and I figured out, that no matter if I chose the legacy-layer with nrf_drv_twi-functions or the new nrfx_twi...
Hello,
I wanted to ask the community/Nordic for protocol advice for a specific application. I want to connect a series of sensor modules in a hotel. The sensors are in adjacent...
there are proxy client and proxy server in the light switch demo of mesh sdk v2.0.1.the proxy client can't be provisioned after i had provisioned another client,is there only...
Just starting development with nRF52840-Preview-DK using Bluetooth Mesh.
I've loaded compiled, Light switch server example code for nRF5_SDK_for_Mesh_v2.0.1 along with nRF5_SDK_15...
Dear all:
I want to know how to demo the proxy client & proxy server ,I can't find the way to demo the two samples which like the PyACI do .
For example ,I can use a button...
Hello,
I am develop a project with nRF52832 and I use nRF5_SDK_14.2.0 and softdevice s132.
My problem is I need create a variable that maintains the value after of the...
I have configured nRF8001 with Arduino M0 Pro board and its working properly. Now, I want to add passkey to my device but it dont have display/ keyboard , only one power button...
I have nRF8001 configured with Arduino M0 pro, and I am having problem regarding how to set static passkey. I came across the fact that softdevice API can store static passkey...
Hi, I just recently bought nrf52832 dk board. I am really new to this. I have prior experience on Arduino only. I started working on nrf52832 dk board with the help of nordic...
Dear Nordic Team,
We are using nRF52832 with a IQS231A for proximity detection for a new product, the pins are connected to SDA and SCL and everything is routed as in...
