Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
I'm developing an application that will run on a board without externel oscillator for RTC1 and it means no app timers support.
I started from ANCS example and...
Hi, I tested to run BLE Mesh(v1.0.1) light switch example using SEGGER embedded studio(SES) on Windows10 and three nRF52DK(ntf52832) boards .. one client, two servers. It...
Hi,
I encounter the problem when using the mcuboot with zephyr 1.11 is that the system keep rebooting.
mcuboot: https://github.com/runtimeco/mcuboot
mcuboot build...
Reference: bbc micro:bit (microbit) board Eagle schematic files
I heard that bbc's micro:bit board is based on Nordic's nRF51822 & build by Nordic Semiconductors
Since...
Using SDK14.2.
I'm trying to optimize the throughput of my ble_nus-based app (I'm getting about 5k/sec right now). I've read elsewhere on this forum that increasing NRF_SDH_BLE_GAP_EVENT_LENGTH...
Hi.
I am trying to program the ble beacon application example that requires the S132 softdevice. I am following the instructions that request the device be erased first...
Hi,
I'm looking for feedback on the feasibility of using Bluetooth Mesh to network Bluetooth modules in a series of adjacent hotel rooms. All the nodes are also relays since...
Hi!
I have a Nordic nrf51822-DK. I'm need send large data to the Android phone (10 mb).
I'm use sample devzone.nordicsemi.com/.../dealing-large-data-packet-s-through-ble...
This may not be the place to ask this question but have to start somewhere.
1. Using an Adafuit BLE Sniffer nRF51822.
2. Ble-sniffer-osx, Version 1.2. 4 (build 28)
3...
According to the answer here , Nordic currently doesn't offer a proxy node implementation.
What would be the best way of getting started to create a proxy node? Are there...
Hi,
My device is peripheral and server and is connected to an (android) phone. I have two related questions:
a) I understand that maximal packet size is obtained by calling...
Hi!
I'm trying to log the flow of communication in the Light Control example of the Mesh SDK. But when I log all the received network messages on a server, I also get a...
Hello
I would like to check coded phy performance
in order to do so I need to achive the following:
1. change to coded phy on default (as I ub\nderstand can by...
I am getting BLE working on an nRF52832, and I am a bit confused as to what I should be setting RADIO->CRCINIT to. I was hoping someone could clear this up, which is more...
Hello
I m trying to measure the current in my development card nrf52DK using the power profiler kits, so i prepared the board by (cut the PCB track shorting solder bridge...
