Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hi....
I have a problem when i use dfu_dual_bank_ble_s130_pca10028 in sdk v11 on my board. cpu is nrf51822QFAA.it seems reset all the time. using keil debug, it's wrong on...
The CoAP block example has a "put" function, which works just as the instructions describe. It would be helpful if you could also show an example of the "get" function. These...
hello!
Is IoT softDevice for nRF51 DK has all the features of BLE 4.2??
I know IPSP is the feature of BLE 4.2, but i wondered whether privacy and data packet extension...
app : nrf tools on git hub
s130: sdk v11
s110: sdk v8.1.0
example : nrf_ble_uart.
after modify, it happen, is there some definition shoud modify in app?
by the war,the...
Hi All,
I'm using Nordic UART App to write 'A' to TX characterstic and then i expect some action after that as per my code on BLE nordic device, which is happening.
But...
I'm using the attached proximity_setup.xml ( proximity_setup.xml ).
I'm trying to use the Battery Service to send Battery Level notification.
I added the following code...
Hi,
I have just received a nRF52832 Preview DK and I am trying to set it up according to the description in the nRF52 Series - Get Started section.
I have connected the...
Hi All,
I am using nRF51422DK with SDK 10 and trying to communicate with an external peripheral over UART at every timer interrupt.
I have modified the ble_app_hrs example...
Hi All -
Is there anyone successfully able to autoconnect with nrf51822 with a phone/pc/tablet? I have been trying it for the past week and couldn't get my nRF51822 autoconnect...
I successfully turned off bluetooth radio using NRF_RADIO->TASKS_DISABLE = 1 when i do advertise_start(); after certain delay i coudnt connect back for data transfer
Based on nRF51822\Board\pca10001\ble\ble_app_hrs example,
How nRF51822 detect ADC input? Which ADC pin?
Configuration code:
NRF_ADC->CONFIG = (ADC_CONFIG_RES_8bit <<...
Hi, I'm having a problem with calling pstorage_register(); The first I call pstorage_register() is just fine, but the second I call return the nrf_invalid_param.Here is the...
Hi......
the board advertising correct,and it work normal (connect,send and receive data),bug it's name can not display in app scan menu. the definition is "liu",but displaying...
Hello,
I have been trying to use the nRF52 preview DK board as a master device with another chip as its slave device. Now I know that to read or write the function used...
The statements
NRF_PPI->TASKS_CHG[n].DIS = 1, and
sd_ppi_group_task_disable(n)
cause a hardfault when NRF_UICR->CLENR0 is set to the start of the application code, but...
