I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hello,
I am getting the following error in Segger Embedded Studio v5.60
SEGGER Embedded Studio for ARM Release 5.60 Build 2021081102.47262 Nordic Edition Windows x64 ...
Hello,
I changed saadc.zip for my application needs
and would like to plot the incoming serial data from ADC as asked in
For time evaluation I would like to have...
Hi
We would like to test the “Carrier frequency offset” of the PCBA during production. Like the BT SIG test: RFPHY/TRM/BV-06-C [Carrier frequency offset and drift, uncoded...
nRF5 SDK, SD140 7.2.0
I am running a bluetooth application that also has OTA DFU capabililty via bluetooth. In my normal application I use a timer to advertise for exactly...
I need to set the SPI Mode NRF_DRV_SPI_MODE_0 for a 2nd chip (on the same SCK/MISO/MOSI) to NRF_DRV_SPI_MODE_1.The chipselect is handle by the application.
I can't do the...
Hello,
Is it possible to clone services of peripheral device connected with "Bluetooth Low Energy Standalone v4.0.0" PC application? I see it is possible in "nRF Connect...
nRF52840
NCS 1.9.1
I have successfully downloaded app_update.bin to flash and rebooted. MCUBOOT copies the new application correctly and it runs fine.
The boot process...
I opened an issue on GitHub, but the NRF Connect iOS repo has not been updated recently. Here is the link: https://github.com/NordicSemiconductor/IOS-nRF-Connect/issues/118...
Hi guys.
I'm using the development board NFR52840DK and I modified the sample in zephyr\samples\boards\nrf\nrfx to use twp buttons, sw0 and sw1.
The sw0 button reset a...
Hi,
I want to use my PC to send some message to dongle via USB, then the dongle send them to certain device via BLE.
If there is a sample that allows PC interacting with...
Hello,
I have tried running Blinky example with some Low Power directives in the code without success. I came here for help then.
The current consumption used by the example...
Hi All,
I am trying to port my current SES project (s140) from nrf52833 to nrf52832. My nrf52832 is spec'd at 512kb flash and 64kb RAM. Any help would be much appreciated...
Hi,
Trying to evaluate the nRF52840DK with Matter examples but none of them seem to compile.
Following error is the result
Building light_switch west build --build-dir...
Hi,
We are using nrf5340 nrf connect SDK V2.0.0 and we are unable to find the brownout detector configuration. For our use-case we want to trigger system reset if supply...
hello Nordic
i work with nrf52832, with ncs 1.7.1 (moving soon to 1.9.2)
i have some issues with my spim clk and i think (not sure) its related to working with spim0...
