I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I'm working on a tone library. I'm using timer2 and ppi channels to generate 50% pwm signal.
It's working fine.
Now i want to add another timer comparison ( timeout...
I am trying to see if there is a way I can generate a multi frequency audio signal without additional hardware. I am talking about something similar to DTMF. The audio wave...
Would you please tell me how to use the nrf52832 PWM interface to implement differential output to spkr?
Here is my PWM interface configuration code:
NRF_PWM0->PSEL...
I am working on a device which also needs to give audio feedback to the user.
The app on the mobile phone needs to send a wav (or similar) file (mono, speech) to the device...
hi, I am using nrf52832 development board for PWM and I want to play an audio (.wav) file using PWM, I am unable to play the audio clip using the PWM, and same audio file...
Hello,
I'm using SDK15.3 and trying to do a non-connectable advertising while connected.
For that I set my adv package as non-connectable, however, when I run the function...
Dear Nordic Team,
I have a BLE application that we developed on nRF52840 DK for S140 based SoC and this application is working fine on the DK Board.
Now we would like...
I am using IAR version 8.30.2 . When I try to build the example project is the nRF5_SDK_15.3.0_59ac345 for 802.15.4 for the wireless UART I get a build error:
wchar_t in...
When I start my nRF9160 modem (AT+CFUN=1) it can sit in CEREG mode 4 (unknown) for a couple of minutes, before it switches to 2 (searching) then 1 (registered).
Is that...
Hi
I am trying to implement UART on nrf52832 , s132 central and peripheral code.I am getting the following error.
Description Resource Path Location Type fatal error:...
I'm trying to change advertised manufacturing data during advertisement after pressing a button on the nRF52840 DK board. Seen many examples using the call ble_advdata_set...
Hi everyone!
I am currently working on a custom prototype that is using the nrf52840 chip and sdk 15, and now want to perform DTM tests on the device. Looking at the DTM...
Hi! We're developing on an NRF52840 and are trying to understand what the meaning of the specified 'recommended usage' is, as its specified in the aQFN 73 ball assignments...
