I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
My setup consists of a Raspberry pi and a PCA10056 dev-board (NRF52840). I followed the instruction from here in order to set up the Raspberry pi as boarder router and connect...
Hi all,
I am working on the Smart remote and when "spamming" a lot of key simultaneously, I sometimes get a warning "m_coms : packet lost" and then a disconnection.
...
Hello,
I have a Taiyo Yuden EYSHSNZWZ module. I also had a breakout board manufactured for it to get access to all the pins. I am having trouble trying to program the...
Hello,
I`m trying to get this ( https://github.com/NordicPlayground/nrf52-ble-multi-link-multi-role/ ) working properly to test the possible working range between two nRF52840...
To the kind attention of the Nordic support team,
Hi to you all, I have got legacy gazell code running on nRF24. In old code the following instructions was used:
hal_nrf_set_address...
My customer wants to do a range test with a propritary 802.15.4 software.
Do you have an example for the nRF52840DK with an blinking led if the communication is established...
Hello,
i want to display a string in 5x21 led matrix using HT1632 Led driver
Using SPIM0 Protocol i should send data from nrf52832 to HT1632 led driver
My question is...
Hello,
I am working with the mesh SDK 2.1.1 version and the Light switch proxy server and proxy client examples.
Everything is working fine between client and server...
Hello,
We are designing a board based on nRF51422 and we are working with a company based in a different country for Android/iOS app development. They bought a nRF51 Dongle...
I have downloaded the latest nrfgo, but the version of jlink is 5.12V.jlink5.12 does not support nrf52840,so i updata it to jlink6.40,however nrfgo still can't download the...
Hi All,
I am Using the NRF52840 DK Device for my application development
I want 2 UARTS for my application
I have used the example - nRF5_SDK_15.3.0_59ac345\examples...
I am currently developing a central device based on the NRF52832. I am able to discover and get handles to all the services and characteristics of interest on the peripheral...
Hello,
I wanted to know if I can use AT commands to communicate with nrf52840 DK.
If it is possible, do I need to have a separate firmware or is nordic sdk enough?
Hi, I am new to FreeRTOS and am planning to change to some of my code routines to FreeRTOS because my code has been expanding and in need of priorities interrupts. I face...
