I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Is the Altium integrated libary used in the Altium files for the nRF9160 DK available anywhere? It is not included in the hardware file download on Nordic's website.
Looks...
The problem is shown in the picture below.
It is normal for 10 seconds after activating the timer.
As you can see in the picture, the value of the time stamp changes...
Our application uses and external nand flash to store the data samples. The collected data is then be transferred using USB. So we chose usbd_ble_uart example and wrote code...
Hey,
I am working on mesh with nrf52 DK. I want my device to work on battery for long time, I have enabled the MESH_FEATURE_LPN_ENABLED macro in nrf_mesh_config_core.h file...
I'm returning an error code on a rw_authorized characteristic using uint32_t sd_ble_gatts_rw_authorize_reply(uin16_t conn_handle, ble_gatts_rw_authorize_reply_params_t * auth_reply...
When using the PB-ADV bearer there is a ~10 second delay after the Link is closed and the mesh stack starts working again.
This is related to my previous report https:/...
I am trying to develop a SPI interface to a CANBUS controller for the nRF9160 for the zephyr platform.
The issue I am having at this point is is that I am unable to see...
Hello,
I am working on a custom pcb with nrf9160-SICA. I have UART SPI and GPIOs running fine but I am having a very difficult time with I2c (TWI).
Pins 8 and 9 are occupied...
Hello,
I'm trying to use the nrf52840 Dongle on the Raspberry 3B+. I didn't achieve to run an appImage downloaded from your site. When i'm executing the app nothing happens...
My current hardware is based on SoftDevice SD132, v6.0.0 as provided with SDK 15.0.0. I would like to update it to use SoftDevice 6.1.0 (as part of SDK 15.2.0) and perhaps...
Hi all,
I use nRF52832-QFAA, S132 2.0.0, SDK 11.0.0, IAR 7.5 under Windows
Upon connection, I am trying to resolve the peer "random private resolvable" address (not for...
we have designed a board using Nrf9160 IC and we have issue with SIM module. we not getting 1.8 volt in "SIM_1V8" pin. when running mqtt sample program we are getting
...
Hi,
Using nRF52840 with SDK15.0.0.
I started my projetc based on BLE tutorial characteristics.
I created my service and add 2 characteristics successfully.
My module...
