I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hello,
I am using ble_app_uart example in sdk 15.2 and nrf52832.
I am using this example to communicate with other MCU. It is continuous Rx Tx between nrf52832 and other...
Hello,
I am currently implementing a security protocol from the IETF LAKE working group called EDHOC in Rust. I am using nRF5340dk and the bare-metal Rust examples from...
Hi there,
I am currently following this following tutorial on building a Matter setup.
When trying to build the openthread coprocessor I am hit with the following error...
I send and receive 1:1 using an ESB with nrf52840. I do not want to "use nrf_esb_start_tx()", but instead use PPI to trigger a specific event to be sent.
I want the PPI...
Hello
I am using nRF52833 based BE33 ( Celium Devices ) and using nRF52SDK17.0. Recently I have encountered the below issue:
err_code = app_timer_start(m_loadcell_timer_id...
I use 52833dK,Wpanctl whether there is a command to send custom data in the thread network.Similar to UDP in cli.
I found that there are relevant codes of HDLC software...
Hoping someone can help.
I am using an nRF52840 MDK USB dongle running nrf firmware in wireshark / nrf sniffer. I am attempting to sniff the bluetooth messages from my pool...
Hello,
I'm trying to get SPIM working with a nRF52840 DK, PCA10056.
I downloaded the nRF5 SDK 17.1.0 and I am able to build example projects, and I verified that I...
Hello,
Do you know where I could find a sample to read NFC Tag with Thingy91 ? The best could be to have a sample sendind on MQTT NFC tags reads.
I read different posts...
Hello, I need help to clarify an idea. What I want to do is get data from a Main board (Custom uC with sensors) via UART and connect it to the UART set pins (29 and 31) of...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056...
Hello,
I have a custom board using an nRF9160 chip. It connects to the Nordic Cloud. Modem firmware 1.3.1. SDK 1.6.1.
I have seen an issue 3 times now over ~6 months...
Hello, guys.
I have nRF51822 SoC running Zephyr OS. Among the other things, the nRF should communicate (over I2C) with the touch controller that will fire an interrupt every...
Hello,
I am using nRF52833 based BE33 ( Celium Devices ) and using nRF52SDK17.0.2. I am a beginner at Nordic. I want to understand how I can access a pin named " P1.04 ...
Hi,
I faced the exact problem nda , here . I take step just like nda did before. I unchecked "Enable debug options" as Marte Myrvold told, but still the same problem.
...
