I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hi ,
I use nRF52810 with SDK 15.2. Application was Gazell protocol.
However , the link error would show the library use FP feature and build was failed. Both failed at...
Hi
I want to get the RSSI value of the received packet through the DTM test routine. Here is my DTM test routine, where I changed it
I got the result
>> RSSI: -127...
Hi
I am trying to create ble mesh network using 4 different N52832 module. But every time i tried to connect with the network, received the initial configuration failed...
Hi,
I'm interested in using Gazell and have managed to get the gzll_ack_payload Device & Host examples working successfully between a pair of nRF52840 devices on our custom...
I tried to install the latest nRF Connect (3.1.0) on my Windows 7 dev machine and it did something to wipe out my USB setup (froze up during install of JLINK). So I had to...
Hi all,
I'm working on a board equipped with a nRF24L01+. It is PIC32 based and I'm writing a mini driver for it. So far my SPI and API seems to work correctly:
...
I wasn't able to find any documentation or examples for the BL-651 chip which is meant to run the same code as the NRF52 bluetooth chip.
I'm having trouble running it on...
Hi everyone,
I'm using a Si7051 I²C temperature sensor connected to a nRF52840 and I found some very weird behavior of the TWIM module. Firmware-wise I'm using the mbed...
Hello All My English is not good, so Sorry I have a question like this
I have self BLE unit - EYSGJNAWY-WX from TAIYO YUDEN firm That has nrf51822 CPU and 32.000 crystal...
Hi there,
I would like to know why v4.22 version of SES doesn't have "nRF Connect" tag under " Tools→Options "
also I even can't find "open nRF Connect SDK project" option...
Hi,
I have an app that uses freeRTOS
My app runs OK , however when I am debugging it in segger studio with my SWD connector, it crashes with no reason
If I check the...
Hi,
Do you have a basic Android Studio App that can connect send and receive from an nrf52832 based board already programmed?
I know the protocol strings I need to send...
Hi I am porting my application from SDK12.3 to SDK15.3.
I am facing error during advertising. Below is the code snippet and error is invalid param (0x07).
For scan response...
Hello everyone. I am working on an RTLS application that uses BLE's RSSI measurement method (Using nRF52840 dongle) to locate a human. The system has 3 components:
Beacon...
Hello, It looks like if there is an issue with bootloader DFU. If no connection timeout is right. But if you starts a DFU late (near the end of the timeout), il will cut during...
