Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hi,
Is it possible to provide eagle design files (layout and schematic)? I see that you have provided for altium designer.
Also, is it possible to provide eagle library...
Looking for the best ways upgrading from a nRF5 SDK / SoftDevice based design to Zephyr. in my case, the nordic bootloader / upgrade process is configured for UART.
It would...
When using custom 128-bit base UUIDs and 16-bit UUIDs to address services or characteristics within the formerly specified base UUID, it seems the Nordic softdevices always...
Hi, I am using nRF24AP1 for ANT+ purposes and I am looking for continuous scanning mode (the radio is active in receive mode 100%). The command Open Rx Scan Channel (0x5B...
when I have the line in my sdk_config.h, it overrides the and I end up with undefined reference errors.
right now I had to comment out the line to be able to compile the...
Hi,
I need to print the RSSI value to the nrf app or putty terminal to check the RSSI value.
I have gone the structures "ble_gap" file to get the RSSI value and calling...
Hi everyone
The following code is initiaizing the uarts correctly,but there is unpredictable behaviour in this case.
Whenever i disable the 1 UART sensor, works fine....
Hi all,
I am very new to the field of BLEs now I bought one BMD300 Evaluation board,and I want to use nRFgo Studio for the development is it possible to use nRFgo Studio...
Hi,
we are using nRF52832 ADC in differential mode. We have two channels connected, where other is presenting reference voltage 1,65V and other is +/-1,15V on top of that...
Hi. I am developing based on the multi-link central example. In the below code the PHY is set to BLE_GAP_PHY_AUTO.
I don't know if my example therefore is running at 1Mbps...
I saw several threads that talked about this, but I could not decipher an exact answer, so apologies if this is a Re-Ask.
I recently purchased a nRF52840 Dongle with the...
I am not able to Control GPIO PIN 14 In this program(BLE_UART) this PIN gets powered continuously . When the device connects to NRF App the power supply becomes Zero and after...
Hello.
Im in a stage where I need to transfer over our current old (ancient) libraries for SPI communications to a NRF52, where we use SPI to communicate to a certain slave...
Hello,
I have set up the Development Kit according to the following instructions and successfully activated the SIM card.
www.nordicsemi.com/.../GetStarted
Unfortunately...
