I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi all,
I am having ADXL335 Acellarometer board. Here its giving data of X,Y and Z axis directly in analog form.
So how should i configure my IO pins of PCA10001 board...
I've been reading about minimizing the amount of time that the SoftDevice blocks the CPU for, but most of the answers have to do with old revs of the chip and old versions...
We have a peripheral device that we would like to have sleeping 99% of the time. I have a single timer waking it at 1-second intervals to look for things it might need to...
Hi,
I am trying to get date and time on my nrf51822 but struggling a bit. I would like the nrf to receive the time over BLE and then increment it internally using the RTC...
I have a system using the Gazell link layer in which 2 devices stream data to a single host. Each of the devices is assigned a different pipe, and all three (host, and both...
I have successfully set up UART/Serial Port Emulation over BLE example. I have modified it so that it works with two nRF51 DKs, one acting as a central and other acting as...
Hello,
I would like to know whether the below PA can be interfaced with nRF51822?
For our application we need to increase the power of the BT. so I have selected the below...
Hi,
From other forum posts it seems to be very important to follow the reference layouts when designing nrf52 PCBs, but I can only find the reference files in Altium format...
Hi,
I have a nrf51 dongle and I try to connect my Android smartphone to it. My smartphone is BLE compatible, so no problems here.
I flash the firmware using master control...
I am a newer for Nordic's BLE.
and has WaveTek nRF51822 BLE Shield (design for Nordic), and downloaded the S110 softdevice version 7.3.0 and the wavetek_connectivity _s110v1...
Hi
I have some problem about the HomeKit SDK,is there anyone could help me?
In the HomeKit SDK,such as lightbulb project,there is a function mfi_i2c_configure that...
Hi Nordic guys,
we are developing a peripheral device with a custom protocol to exchange data.
we are using nrf51822 with SDK 6.0 and SoftDevice 7.1.0 (s110 being peripheral...
I can not find information about layer stack-up and whether the via-in-pads were filled, please provide this information. We are thinking about a variant with thin outer layers...
Hi, I am trying to combine SPI, microESB and BLE. BLE and microESB will not be combined in realtime, but rather be two distinct modes, and not run at the same time, and therefore...
