Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Dear all,
I tried to program and test the iBeacon application on the s110 folder from nordic examples.
The code on the Cortex-M0 has problem. Seems during programming...
After program nrf51822,it works normaly.But when I program again,it can't debug.NO SWD and NO USB DEVICE.So I can't use nrfGoStudio or nrfjprog.exe to recover it.When I pull...
Hi,
I've set up a streaming solution that is easily streaming 4+kBytes/s to an iPhone. I've also set up an ADC service that is sampling at 2,083 Hz 10 bit mode, using a...
Hi,
I am using nrf51822 (128k).
Softdevice 6.0 (s110), SDK 5.2.
How can I send an empty notification packet (data length 0) to master device?
If I send a packet with data...
I was wondering whether it is safe to use a delay (such as implemented by nrf_delay_us) to, for example, delay an iteration of a while loop, or that it is always better to...
Dear Sir/Madam,
I am testing iBeacon application on the nRF51822 mounted on nRF6310 motherboard.
I programmed the ble_app_beacon application in the keil_v5\ARM\Device...
Hello,
I get a sample code in the dir flllowed after intsalling nRF51 SDK:
\Keil\ARM\Device\Nordic\nrf51822\Board\pca10001\s110\ble_app_beacon_code\main.c
but I still...
I ve installed CSR bluetooth 4.0 adapter , it can communicated with even the bluetooth 2.0 devices, how ever it even can not discovery the board when I programed the softDevice...
Hi,
I have ordered nrf51822 development kit with one of my local vendor. when the product came to india , it was checked in customs office somehow the samples in the kit...
I'm using an nRF51822. Currently, I'm using the low power sleep mode. The device uses about 1.5 uA in sleep, which is great. The firmware wakes up the device every n minutes...
I have a fully functional code for 8-bit data acquisition using nrf24le1. Now i want to upgrade it to 12-bit resolution ,but i have problems in doing so .
In my project...
I am making a module using nrf51822 and a chip antenna.
I need a layout from nrf51822 to a chip antenna through matching chircuit.
Unfortunately, I don't know how to...
Hi,
1. I want to design a product as a tag,which can read the temperature and transmit the data to a host,the host can read several devices' data. which mode would I use...
Hi everyone,
Just recently I've got two nRF6310 EVB boards with a nRF51822!
When I connect board via USB and open the nRFgo Studio, it can recognize the board as nRF ISP...
For nRF5122 BLEStack, it is analyzed that the event is processed in each of the interrupt handler for the interrupt terminal BLE
I understand that is processed through the...
