before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi all,
I have plenty of experience with the Old SDK, IAR/Keil/SES, nRF51, nRF52, Soft Device, etc. However, I'm new to the nRF Connect SDK, VS Code and nRF5340. I've successfully...
Please let us know which PINs of nrf5340 are used by BLE stack and which pins are used by peripherals like UART0 and UART1? We are converting our code from nrf connect V 1...
Hello,
We are evaluating MCU's for a low cost Central device that is extremely cost constrained. The nRF52805 and the nRF52810 both have the same RAM (24 KB) and FLASH ...
Hello,
I'm stuck in the nRF Connect SDK Fundamentals course on lesson 3, exercise 1. When opening the COM port to view the printk messages, I get an error when connecting...
Hi,
I am working with nRF5340 and nRF Connect v2.7.0. When I try the mass sample it works fine. When I take the code to my custom project, I have
ff.h no such file or...
Hi,
I am currently working on communicating between the nRF5340 DK and the nRF5340 Audio DK over BLE. Could you please share the information flow?
Warm regards, Rajendra...
Hi,
We have modified the throughput example of NRF5340, v2.6.1 SDK to achieve around 600 Kbps for iOS app. Attached is the sniffer trace.
Can anyone confirm that the data...
I'm seeing duplicate data packets while analyzing our sniffer trace from NRF5340 to iOS app. However, there is no packet loss or any impact on data rate.
What might be the...
Board: nrf5340dk (build board: nrf5340dk_nrf5340_cpuapp) / SDK: v0.16.8 / I'm a complete beginner who touches the nrf board for the first time My Project: max30101 --(measured...
Hello
we have some own created UART drivers which access the UART registers directly.
Those drivers have been working withe the older chip revisions for years.
Currently...
Hi,
I cannot resolve the problem while setting up modem trace RTT logging. I'm also unable to find up-to-date information on how to set this up.
I have connected DK as...
I'm close but this is not working for me yet. I'm trying to send a few hundred bytes from android to my nrf device. So I tried to implement long write where you set prepare...
Hi I've a side request, into the exercise I've to perform some changing into the DK programming interface through the JLink, so the question is how to restore the predefinite...
I am getting an fs_close() -5 error (-EIO) when I write to an SD card using fatfs. I determined this error was associated with FR_DISK_ERR in fat_fs.c.
Additional info ...
Hi,nordic team，
im use nrf52840 develop my product with sdk ncs 2.6.the speed of desktop dfu is so slow,and the speed of configurator channel is also slow.i want to transfer...
