before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I am from China. My company made a BLE module with chip nRF52810. Recently , I coded a program for it by SDK12, based on ble_app_uart example. I modified the corresponding...
I have setup the nRF52840 DK as below
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/how-to-setup-the-thread-demo-displayed-live-at-google-i-o
Setup WireShark...
Hi,
We are currently going to try and implement FOTA/DFU with an nRF52840 controller and an nrf52832 peripheral. Is there any example for how this can be accomplished...
Hi,
I currently have a nRF52840DK pre-programmed with the DFU over BLE, but with the debug version. I am unable to physically get to the device, if I wish to perform a...
Hello,
We are using the SPIS on the nRF52832. We are seeing a higher than expected consumption when it's enabled and not used.
I measure around 7uA extra when enabling...
Hi:
I test the system off mode, I attached a micro vibration sensor. Pulse generated when shaking as follow.
the button config is BSP example default(toggle) , i try to...
Hi,
I am testing the blue_app_uart example and I want to send data
from my smartphone uart terminal app,back to the nRF52840 DK,
Nothing is being received by the segger...
In the latest Mesh SDK, nodes are subscribed to a GROUP address. In previous versions - 2.0.0 I believe - you could also send to a predetermined node.
I am trying to figure...
Hi I am reviewing the nRF52840-DK hardware documentation to make boards with good antenna performance.
Q1. I have divided it into three areas as shown below. Is my understanding...
Hi,
I have been trying to use Keil MDK's Middleware File System with my application. However, when I try to set the Software Component under Manage Run-Time Environment...
Hi, I am from China. My company made a BLE module with chip nRF52810. Recently , I coded a program for it by SDK12, based on ble_app_uart example. I modified the corresponding...
Hi!
I am using the Segger embedded Studio with PCA10056 successfully. Now I have to evaluate LARD DVK-BL654 (because it has external antenna). I found a guide which says...
I am trying to flash my custom board that uses the Raytac nRF52840 via SWD. I am trying to flash a custom bootloader onto the chip; however, JFlash is giving me an error....
Hi, I am from China. My company made a BLE module with chip nRF52810. Recently , I coded a program for it by SDK12, based on ble_app_uart example. I modified the corresponding...
Hi there, I'm using nrf52840 with OpenThread SDK and I wanna know, what is default radio mode of this device? Because we also have another project with Bluetooth and we observe...