Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Using SDK14.2.
I'm trying to optimize the throughput of my ble_nus-based app (I'm getting about 5k/sec right now). I've read elsewhere on this forum that increasing NRF_SDH_BLE_GAP_EVENT_LENGTH...
Hi.
I am trying to program the ble beacon application example that requires the S132 softdevice. I am following the instructions that request the device be erased first...
Hi,
I'm looking for feedback on the feasibility of using Bluetooth Mesh to network Bluetooth modules in a series of adjacent hotel rooms. All the nodes are also relays since...
Hi!
I have a Nordic nrf51822-DK. I'm need send large data to the Android phone (10 mb).
I'm use sample devzone.nordicsemi.com/.../dealing-large-data-packet-s-through-ble...
This may not be the place to ask this question but have to start somewhere.
1. Using an Adafuit BLE Sniffer nRF51822.
2. Ble-sniffer-osx, Version 1.2. 4 (build 28)
3...
According to the answer here , Nordic currently doesn't offer a proxy node implementation.
What would be the best way of getting started to create a proxy node? Are there...
Hi,
My device is peripheral and server and is connected to an (android) phone. I have two related questions:
a) I understand that maximal packet size is obtained by calling...
Hi!
I'm trying to log the flow of communication in the Light Control example of the Mesh SDK. But when I log all the received network messages on a server, I also get a...
Hello
I would like to check coded phy performance
in order to do so I need to achive the following:
1. change to coded phy on default (as I ub\nderstand can by...
I am getting BLE working on an nRF52832, and I am a bit confused as to what I should be setting RADIO->CRCINIT to. I was hoping someone could clear this up, which is more...
Hello
I m trying to measure the current in my development card nrf52DK using the power profiler kits, so i prepared the board by (cut the PCB track shorting solder bridge...
Hello,
I am using the NRF52-DK softdevice 6.0.0 and NRF SDK 15.0. The app is based on on the ble_app_template PCA10040e S112 (The final chip will be a NRF52810 that's why...
I want to flash the program in my custom board. I have flash the program in nrf52832 BLE module via j-link using nrf52832 development board. So, how do i confirm that the...
I use the SDK S110, I hopes in the low power(operation the current 100 uA is following), and then sustains every second bluetooth broadcast and every second computing time...
Hello,
I am using sdk 12.2.2 and customised nrf52 board.
My challenge is when I am using sofdevice + app hex file my device takes 4.1 uA current but when I am uploading...
