I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
nRF52840DK devicetree describes both uart0 and uart1 explicitly in nrf52840dk_nrf52840.dts file: https://github.com/nrfconnect/sdk-zephyr/blob/v2.3.0-rc1-ncs1/boards/arm/nrf52840dk_nrf52840...
Hello,
NRF52832 - SDK16 - sd132 7.0.1
I have an issue with ble_db_discovery_start() that return NRF_ERROR_NO_MEM, when I followed the functions call I found the error...
Hi,
I started with the Blinky example and have added peer_manager to the project by referencing the hrs example. Everything is building, but on init() I am getting a hard...
I have two custom pcbs containing the nrf52832 chip with the EXACT same hardware and software.
When I program and run the old pcb,
The old pcb runs OK. It returns from...
I use SDK 15.3 and SD S340 v 6.1.1. Bootloader is designed to do custom update through GSM; code based on secure bootloader ble example from SDK. I have used code that previously...
Hi,
Greetings!
We are using following setup
nRF52832 DK
SDK16.0.0
Mesh SDK 4.0.0
Light Switch Server and Client
Here we would like to understand below things...
HI,
I set RTS,CTS to disconnect in the overlay file.
(Toolchain Manager.0.6.1/NCS1.3.0)
&uart0 { rts-pin = <0xFFFFFFFF>; cts-pin = <0xFFFFFFFF>;
};
warnings occur...
Below are the details of my setup configuration:
SDK Version: 11.0.0 (with changes corresponding to hardware)
Soft-device: s130_nrf51_2.0.0
Boot-loader: nrf51422_xxac_s130...
Hi, I am Working on nRF52840 and using nRF52840-DK.
Below is my working environment SDK - nRF5_SDK_16.0.0_98a08e2 ,
IDE - Segger Embedded studio (windows 10 - 64 Bit)...
Hello! I gonna buy a NRF52-DK. The seller says the following about kit version :" Hello, original imported. The latest version of 2020. 2.1.0 version". Is it correct? I can...
Hi
In my application, I use nrf52811 to relay data to make the data go further. If data is sent from point A to point B, point B receives the data and then forwards to...
Hi, I'm currently implementing AGPS on 9160, nrf connect master branch. Right before every GPS search we are connecting to our own server via CoAP. To minimize data usage...
Hi!
Running the Asset-Tracker routine will fail to connect to the cloud(ncs1.3.0). The serial port displays an error say Failed to connect to cloud, error -7.
Error...
