Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hello!
I have 3 NRF52840 Preview DK's with Q1AAAA revision ICs. I have been putting those to good use, but I want to test some stuff with SPIM at 32Mhz, which I understand...
Hi,
I am using nRF9160DK, nrf v0.4.0, zephyr v1.14.99-ncs1
I have been trying to measure the boot time from when I press the reset to when it gets to the start of the...
Dear All,
I am trying to enable brown out detection to my NRF9160. From what I see in the data-sheet there is a register that you can set the brownout threshold, but there...
Hi,
looking at the ifx_optiga_custom_example in the nRF5_SDK_15.3.0, i see that for the Hashing calculation the oberon backend is used instead the optiga backend, Why? Is...
Hi,
I see your web: https://www.nordicsemi.com/Software-and-Tools/Development-Tools/nRF-Sniffer#infotabs
There are 4 hardware (DK x 3, Dongle x 1) we can choose to used...
Hi,
I am using nRF52832 with sdk15.3 SES
I need to use DFU.
Buttonless DFU
need to program the controller without the wire connection.
Can you explain how DFU works...
Recently, we are using Nordic resources and developing our own application. We have blue tooth integrated in app, also we have display and our own file system integrated on...
Hi,
I'm working with nRF52840 DK and I want it to advertise iBeacon packets.
I tried the beacon example on ble_peripherals from nRF5_SDK_15.3.0 SDK.
1) nRF connect and...
Hello,
My project is on nrf51822 in which I am using BLE and UART interfaces.
There is single UART available on nRF51822 and I am using it for communication with an...
Hi I am using the custom_ble_service example from https://github.com/bjornspockeli/custom_ble_service_example/blob/master/main.c . The example code will turn a custom characteristic...
HERE is the fix for this problem. It has been reported before (by others) with no reply. I hope that this fix or its equivalent will be incorporated into the next SDK release...
I want to interface a 16MB external flash (SPI) with nrf52832 on the development board.Suggest me how should I start with and if there is an example for external flash then...
Hi Great Support Team:
In the spec of 52832, the rx sensitivity is -96dBm @ 1Mbps.
I'd like to know if the sensitivity is the same (-96dbm) while we adopt ANT+ protocol...
I am using the nrf52840 with freertos and bluetooth (based on the HRM example). Application is designed to sleep for a set period of time before the RTC timer wakes the MCU...
