Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Hi
I have below requirement on NFC using SDK 12.3.0 and soft device S132. please suggest how to start with the same.
1.NFC operation. (Simple Read Write into NFC Tag Memory...
Hi,
I'm working on getting the DFU bootloader working and I'm following this blog post.
I'm successfully compiling and loading the bootloader to our custom hardware...
I want two pwm channel output 1MHZ frequency, the phase difference between two PWM channels is 180 degrees。when i set two pwm frequency to 500KHZ, use the configure below...
Hi,
We are testing an evaluation board nRF9160-DK with the firmware samples to build our own prototype. Is there a friendly process or example for FOTA to update the device...
Hey
I would like to know how can i connect 1 peripheral to multiple centrals(ex : 2 centrals), I am have three nRF52 DK boards for two centrals and one peripheral, My idea...
Hi,
Currently I am adding DFU support to our application, I was able to compile the secure bootloader example and use it.
my next question is, how do I enter DFU mode...
Using Rowley Crossstudio for ARM.
Using SDK V15.3.0 and S140 V6.1.1
When calling sd_softdevice_enable(..) it returns 0x1001 ( SVC handler missing ). Any suggestions ?
Hello Nordic Support,
Using the Nordic Power Profiler Kit v2.6.2, I can get the average current consumption for a maximum window of 120 s. Is there a way to get the average...
Hello Nordic Support,
Using the Nordic Power Profiler Kit v2.6.2, I can get the average current consumption for a maximum window of 120 s. Is there a way to get the average...
At present, I have a project that needs to add dual uart function, but 52832 does not have hardware dual uart function, so I need to simulate one serial port, I need your...
Hi all. I try to implement ble dfu bootloader project via getting start from SDK/examples/dfu/secure_bootloader/pca10056_ble_debug project.
Using:
OS: Linux
Compiler...
Hi!
This is a general question about iOS app distribution, but it regards our use of Bluetooth Mesh. I know it is each company's own responsibility to make sure they comply...
Hi there,
I am porting existing code from nRF52832 to nRF52840, and found that bootloader references to NRF_BPROT fail:
Apparently becuse the nrf52840.h in the mdk does...
Hi All,
I have loaded in the Bluetooth Mesh Light-Switch example and it works well.
For now, I would like to read out the received data from the switch node (client) to...
Hello! I am using SDK 15.3.0 to develop the NRF52832 firmware. At present, I want to implement a function, when the device is connected to the IOS host, start pairing, and...
