Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Dear Nordic Experts, A few short questions about mesh advertising in regard to Softdevice s132, 7.3.0, Mesh SDK 5.0.0 and nRF5 SDK 17.0.2:
How do you change the advertised...
Hello,
I'm running asset_tracker_v2 from v1.9.1 on a LTE-M network that does not give the time (UTC clock) info.
When no time information is given, the application should...
Hello
I have some questions about flash_fstorage example.
After reading the macro, it seems that fstorage will be located in .fs_data flash zone.
start_addr is set...
Hi,
Softdevice - 112
sdk 17.1.0
I am trying to evaluate the memory of the device. I am using nRF52810 and the datasheet says 192KB flash and 24KB of RAM available. ...
Hi I am using Unity test framework for generating unit test report and i also want to generate the code coverage report of the code for that i need how many lines of code...
Hey
I'm currently writing a thesis on IIoT and implementation in remote areas. We're trying to setup the nRF9160DK as EON device with all implementations on the board...
Hello,
I am experiencing trouble with NRF9160 chips that get stuck after typically 1 to 2 days of operation. This happens on all 6 boards that I have available. I'll describe...
Hi,
I am coming across an issue with app_scheduler and FDS.
While waiting for an event in FDS to complete (write, read, init, gc, etc) I go into a while loop calling app_sched_execute...
Hi,
What is the lifespan of nRF52810, operating at room temperature ? How long can it reliably work? Do you have some figures on this ? If yes, is it same for other nordic...
Hello everybody
I am using the nRF51 Dongle to connect via a third party app to a measuring device. This always worked very well on my first computer, the app could detect...
Hi,
I updated my Segger Embedded Studio for Arm from V 5.68 to V 6.20a.
Calling CMSIS Configuration Wizard fails with all examples with message : "Error starting process...
Hi All,
I have a nRF52840DK and looking for a solution to connect the VCOM serial port to the PC, without using USB. I will need to connect the serial port to another board...
I'm working on porting a code base over from nRF5 SDK to nRFConnect/Zephyr. Our previous implementation uses ChaCha-Poly encryption, accelerated by the CC310. I wish to continue...
Dear Nordic team,
For the security reason to be safe from the hacking, we like to completely disable the debugging and flashing port during production.
Would you please...
In nRF21540, two antenna ports are for antenna diversity. These two antennas are placed on the receiver side or one of them will act as transmitter and other as receiver?
