Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hey everybody, I am completely new with Nordic devices and tools. Looks like I erased the connectivity bridge application in the nrf52 module at Thingy:91. Now the board is...
Hi,
I am using the nRF9160 to read data from the CCS811 gas sensor, and logs data on LTE Monitor. I am using the BME280 sensor to read temperature and pressure values and...
Hello, I am currently learning to use nRF9160 DK in Guangzhou, China.
It is weird that my China Mobile cellphone SIM card can be used on this DK to connect to Cloud. However...
Experienced developer new to embedded C programming here, so please forgive me if I'm missing something obvious. I already went through the GPIOTE example from the nRF52 SDK...
Hello,
I'm not sure if this is possible, but I would like to filter log level depending on which backend is receiving them. For example I would like to set the RTT to...
Excuse me:
When our tests the RX selectivity of nrf52832, the test results are inconsistent with those in the datasheet(nRF52832 Product Specification v1.4 P232). How did...
Hi,
I am using nRF5340 development board with J-Link connected to "TRACE" pins: SWDIO and SWDCLK.
In app project I have these settings in prj.conf file:
CONFIG_USE_SEGGER_RTT...
Hi Support team,
in the following link, there is a fix decribed to get lowest power down current of the UART0 of the nRF52840:
https://devzone.nordicsemi.com/f/nordic...
Hi all,
I am using the Adafruit Feather nRF52840 as my central device. My peripheral is a nRF52832 with a 9DoF IMU. (SDK17.02)
I need to stream 26 Bytes of IMU data at...
Hello,
we started using zephyr OS for our firmware projects. To implement a propriety protocol on top of IEEE802.15.4 I use the radio with CONFIG_IEEE802154_RAW_MODE =y...
Hello
I am using sdk v17. I am merging the example of ble_app_uart and crypto_aes_ctr.
I added files about crypto and set the file path. However, the path error is printed...
Hello~
I am experiencing hardfault occasionally. (once a day ~ once in 3 days)
I am testing 14 boards to catch hardfault.
The following is my setup
- hardware...
Hello, I was trying to run the sample Alexa Gadget Application on my NR52840-DK, using nrf Connect SDK v1.5.0. However, upon trying to run the application I am getting the...
Hi support team,
I am developing a product. The product needs read adc and restart advertising when no connection.
I get hardfault randomly when called the ble_advertising_start...
Hi all, the application i'm using nRF52810 for requires that I keep the device powered on all the time. However, in the case of errors (tolerable within my application) I...
