The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
Hi there,
We are quite new to Zephyr. We are currently porting our existing app onto Zephyr as a test. We are currently using NCS 2.5.1
So for our existing application...
I needed to add my own partition to the primary flash, and was able to do so successfully by adding a section to the device tree partitions.
However, when adding MCUBoot...
Hi,
I'm trying to setup my NFR52840 DK to act as a NFC tag so that I can read some simple data on my phone via NFC transfer.
I have tried a few NFC sample applications...
Hi,
I am using a modified HTTPS Client demo code [Let's say Version A] and sometimes when trying to debug with Segger Embedded Studio for ARM (Nordic Edition v 5.34a/Jlink...
Hello,
From time to time I am getting the error " Unable to find bootable image" when I start a debug session in SES-NE v5.60.
FIH_CALL(boot_go, fih_rc, &rsp); if (fih_not_eq...
I am trying to read the GPIO state on an nRF52840 right after it wakes up from deep sleep (System OFF mode). I have configured 4 pins as wake-up sources from deep sleep System...
I have been working on finding the cause to an unexpectedly high power power consumption in several newly produced units of our product based on nRF5340. I believe I have...
I'm trying to build a custom secure partition, but get the following error when building:
However when navigating in files to the directory the file "tfm_custompartitiontest...
Hi All,
My team recently reserved a custom service UUID with the Bluetooth SIG, and we'd like to replace the custom 128-bit UUID we had been using in our products. Can I...
HI
We are mass producing NUS-based products.
During mass production testing, pairing is performed and functionality is tested by pressing buttons, etc.
However, pairing...
I'm using
AT_MONITOR ( catch_all , ANY , on_modem_at_notification );
and I'm just printing the notification on reception:
static void on_modem_at_notification...
Hello,
I would like to add to my project new i2c slave (for example - dac5571 from TI). In the DTS overlay - under the i2c0 node I need to specify compatible , and I don...
I have configured the nrf52840 DK one board as Peripheral and other as central.
Added multiple services and characteristics. I am sending some data at every 20ms using notify...
Dear all:
Customer products in normal mode, BLE works normally, all functions are OK. An error occurred in DTM mode during authentication. Procedure The failure status is...
Using the SDK 15.0.0 SPI example (master) to send a single byte.
Sending 0x00:
Sending 0x01:
Sending 0x02:
Sending 0x04:
etc ...
Sending 0x7F:
In all the...
