The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
Hello all,
I want to enable OTA DFU capability to NRF52840 BLE Chip. I am now using Buttonless DFU which works fine using nrfutil. But my question is : how can we update...
Hi
I'm upgrading from SDK11 to SDK12 on the nrf52 and part of that is the secure bootloader. I've created a new bootloader and have this working with the new softdevice...
Hi,
I tried to open the mqtt_simple project on the nonsecure ns nrf9160 DK using SES and after that tried to build and run the project which was successfully done but the...
Hello,
I'm wondering what are the drawbacks of the already burned random static mac address compared to a public mac address. I know the difference between the two address...
I have Wireshark setup with old PCA10028 board connected as a sniffer, FW sniffer_pca10028_51296aa.hex Now I'm working with NRF52 family and sometimes I need to observe some...
Hello everyone ,
i want one central uart and three uart peripheral , i want to connect the central to all three peripheral , if i send data from central , it should receive...
Hi
I have a problem with showing data packets in wireshark. I configured the sniffer according to the instructions. At capturing packets in main window don't show anything...
I want to use UART.
I checked the waveform and UART does not send data. Here is my code. build and run are successful. Any help? I connect UART RX and TX directly, which...
hi... how to make a nordic app to act as a peripheral , i have read one post , in that they mentioned set up to be done in gap peripheral mode . how to do that
IAR 7.60
52840
nRF5_SDK_15.2.0_9412b96
Hi there, I'm trying to do some modification in the bootloader (so that we can write the image to the flash's bank1 using our...
Hello,
I read through the Bluetooth core specification in order to get a better understanding of the information that has to be stored at a minimum if using bonding. But...
Hello,
i'm trying to use ble_advertising_init to initialize my advertising data, but when i use this function like it is used in the examples i get NRF_ERROR_INVALID_PARAM...
When I open device just after I plug it in the PC it work fine, but when I try to do it again (exit python script and run it again) I'm getting Error code 13.
Firmware:...
We are currently in the prototype stage using the nRF9160 and are preparing the firmware for the prototype. We have a few question that we hope someone could answer :)
Will...
