Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Dear all,
When I added more than 4 buttons by modifying the example "ble_app_uart" of nRF5_SDK_15.2.0_9412b96, nRF52832 can not run normally.
Another strangely problem...
Hi,
Just got four 52840 USB dongles, with the intent to evaluate the Nordic BT Mesh. But I've been unable to get even a simple Blinky example programmed on the dongle. I...
Hi all, I've just implemented light switch proxy example and it's working very well. Now, I have three NRF52832 boards, and for instance, I have:
A board in the garden...
Can anybody help me to get out of this error, Error programming through Seggar Embedded Studio,
Additional Load File[0] "E:/nRF5_SDK_15.2.0_9412b96/nRF5_SDK_15.2.0_9412b96...
Hello.
I try to make audio noise meter on nRF52832. I used analog MEMS MIC with OPA which I turn on via MOSFET while before measurement. I'm using SAADC triggering by RTC...
Hi there,
What changes should I have to do to the light switch example to provisioning the client and server using group address instead of unicast address?
I believe...
In our application we need to have the NFC pins configured for GPIO and APPROTECT enabled.
As an additional safety feature I verify the UICR content inside my application...
Or any general how-to documents when the users want to set up any peripheral using the direct register access? I try not to use SDK for simplify and minimize the code side...
Hello,
I'm trying to implement the Gazell protocol for one of my tasks. I understand there is CRC for the data sent from the device to the host. I cannot however find anywhere...
Dear Sir
I'd like to develop the Window APP for Mesh (like nRF Mesh).
And I've face a problem. The ECDHSecret key of the Windows side didn't match the device side(Thingy...
Hi everybody!
I am new to programming with Nordic SDK and have some questions regarding writing applications with secure and buttonless DFU via BLE.
I have looked through...
I am using NRF52840DK with SDK15.2 to test the DFU.
I use Segger Embedded Studio to compile both the secure_bootloader project and ble_app_buttonless_dfu project.
Then...
