Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi,
I am currently trying to work with pairing and bonding between the peripheral and Central device.
I am using two nrf52840 dk one as central and the other as peripheral...
Hi,
I cannot start HFXO on nRF52832. I'm using 32MHz crystal TSX-3225 32.0000MF20X-W0(from Mouser) wtih 12pF caps UMK105CG120JV-F(also from Mouser).
Checked with beeper...
Hi everyone,
I'm trying to set the USB polling rate with the nRF52840 and it seems like I'm stuck at 8 to 9 ms polling (~125 Hz). I'm using the Zephyr hid-mouse example...
I am using this code to create and start transmission, but I cannot find a way to set the MACID to the internal NRF_FICR->DEVICEADDR values
My method with iBeacon is not...
I am currently working w/ a project that utilizes TrustedZone and PSA Protected Storage to read/write to internal flash that's accessible only in the secure partition (I'm...
Situation : custom nrf5340/nrf7002 board (very close to production...). Main image is overflowing available internal flash (with a MCUboot 64kB partition).
Secondary slots...
nRF52832 & nRF Connect SDK 2.6.1
We would like to reserve some internal flash for user configuration data that would be written in production like
and read by FW but...
Hi,
I am working with nrf5340 with the Zephyr OS. I created a custom data section in a custom linker file.
.my_data_section : { PROVIDE(__my_data_section_start = .); KEEP...
Hello,
I spent a solid two hours debugging an interrupt pin that was not working, to discover that the problem appears when configuring a callback in another part of the...
I have been bringing up an application on nRF54L15-DK, and about 50% of the time it hardfaults on initialization. I tracked down the cause to a branch to address 0, caused...
I am currently using DWM3000 EVK with NRF58240DK for a UWB indoor localization system. I want to use the timer to setup a localization period for each tag node. I tried several...
I am currently working on direction finding using the nRF Connect SDK in VS Code. I am using an nRF52811 custom board, and my logs work properly. I wanted to include timestamps...
Hello. I'm trying to control led in gpio pin in addition to LED pin in npm1300. I don't think you need to use resistance in LED pins, Is it the same when using led in gpio...
I am using NRF Connect SDK v2.5.2. Sometimes, after I factory reset my Zigbee router device, it will immediately join a network with PAN ID 000000000000. I get this with my...
I'm trying to move my nrf9151 project over to sysbuild (SDK v2.9.1) but when I try to use a custom board definition, the code fails to start up.
So far I've tried debugging...
